FinishVXS8/VXS5: Black (Not painted, approximate value: Munsell N3)
VXS8W/VXS5W: White (Not painted, approximate value: Munsell 9.3)
Dimensions (Speaker only)
(W × H × D in vertical cabinet orientation)
278 × 430 × 239 mm
(10.9" × 16.9" × 9.4")
176 × 280 × 163 mm
(6.9" × 11.0" × 6.4")
Net weight (Speaker only, 1 piece)8.2 kg (18.1 lbs)3.6 kg (7.9 lbs)
PackagingPackaged in pair
INSTALLING THE SPEAKERS
Install the speakers onto the wall/ceiling with the supplied brackets. Ensure
that the wall/ceiling is sufficiently strong.
Illustrations in this manual are for the VXS5. The installation method is the
same for other models.
Pre-installation (Preparation of the cable)
Use stranded wire for cables attached to the Euroblock connector. Strip
their insulation as shown in the figure and connect them.
Do not plate stranded wires by solder. Doing so will cause the wire to break.
An installed speaker is shown below. Install the bracket base and attach the
mounting bracket as shown.
•When installing the speaker to the ceiling with the grille parallel to the
ground, install the speaker horizontally.
•When installing the speaker to the ceiling, be sure to install the bracket
base with its shaft facing horizontally, and not inclined to the ground.
•Mounting bracket is made to not turn left or right when installing the
speaker to the ceiling.
1Put the bracket base onto the wall/ceiling and mark the position for
the screws/bolts and cables. The diameter of the screw/bolt holes at
the four corners is M6, and speaker cables hole at the center is
2Make holes through the wall/
ceiling for the bolts and cables,
as required, and feed the bolts
and cables from the amplifier
through the holes, as shown.
3Install the bracket base onto
the wall/ceiling. Make sure to
fasten four corners of the
4Pass cables through the gap at
the lower part of the bracket
cover, and put the bracket
cover on the bracket base.
If you want to adjust the slack of
cables last, the bracket cover
can be attached after step 5-6.
Installing to the wallInstalling to the ceiling
INSTALL THE BRACKET BASE ONTO THE WALL /CEILING
About 7 mm (0.3 in.)
1Remove the Euroblock connector.
2After loosening the terminal screws of the Euroblock connector with a
flat-blade screwdriver, insert the cable into each terminal and tighten
the screws. Make sure that cables cannot be pulled out.
Use a flat-blade screwdriver with a blade less than 3 mm (0.1 in.).
There are two acceptable wiring methods.
When connecting with low impedance, take note of the combined
Using Loop-Through Terminals
For this method, cables are connected from terminals 1 and 4 to the
subsequent speaker. If the Euroblock connector is disconnected from
a speaker, all subsequent speakers will not work. This can be useful
to identify which speaker has a problem.
Paralleling Input Terminals
For this method, cables are connected to terminals 2 and 3 of each
speaker. Since the cables are connected via Euroblock connectors,
subsequent speakers can work even if a problem occurs with a
CONNECT THE WIRING TO THE CONNECTOR
Less than 3 mm (0.1 in.)
From amplifier or
From amplifier or
Select the line voltage/impedance (100V/70V/8Ω) and power tap for 100V/
70V line distributed system, by rotating the tap selector switch on the rear
side of the speaker with a flat-blade screwdriver.
•The “X” position should not be selected. The 8Ω position should be
selected for 8Ω audio systems only. If the setting is incorrect, it may
cause malfunction of the speaker and amplifier.
•Make sure the amplifier is switched off before operating the tap selector
1Attach the mounting bracket and safety wire to the speaker. Use the
supplied screws to attach the mounting bracket.
The way to attach the mounting bracket depends on the orientation of
the speaker (vertical or horizontal).
2Set the desired vertical angle of the speaker.
Loosen the angle adjustment bolt with the supplied hexagon wrench,
adjust the angle of the speaker, and tighten the angle adjustment bolt
to fix the speaker (indication of torque: 8 N·m).
•Guide marked on the mounting bracket is every 10°.
•(VXS8/VXS8W only) When installing the speaker to the wall with a
vertical angle of 30° or less, attach the supplied stopper screw.
1Install the mounting bracket to the bracket base.
SET THE LINE VOLTAGE/IMPEDANCE AND POWER
ATTACH THE MOUNTING BRACKET AND SAFETY WIRE
Mounting bracket can be attached in reverse direction.
INSTALL THE SPEAKER TO THE BRACKET BASE AND FIX
Illustration indicates the setting at 30 W for 100 V
line and 15 W for 70 V line.
To the wallTo the ceiling
2Attach the safety pin.
Be sure to attach the safety pin to prevent the mounting bracket from
The safety pin can be attached from either side of the mounting
bracket depending on the angle of the speaker.
3Plug the Euroblock connector into the socket in the speaker.
4Attach the terminal cover.
5(If installing the speaker to the wall) turn the speaker horizontally to
set the angle.
6Make sure the mounting bracket is seated against the bracket base,
then tighten the supplied bolt (indication of torque: 6.5 N·m).
•When installing the speaker to the ceiling in particular, make sure
the mounting bracket is seated against the bracket base.
•The bolt with hexagon hole can be attached from either side of the
mounting bracket (left or right) depending on the angle of the
7Install the safety wire to the wall/ceiling.
•Make sure to take measures to prevent the speaker from falling
down in the event of a installation failure.
•When installing the safety wire to the wall, install it higher than the
wire’s attachment point on the speaker, with as little slack as
•If the safety wire is too short, prepare another wire appropriate for
the speaker weight and installation conditions. If the wire is too
long, should the speaker fall, the wire may snap as a result of too
Bolt with hexagon hole
Surface Mount Speaker
Broj pitanja: 0
Imate li pitanja u vezi s proizvodom VXS8 trgovačke marke Yamaha ili vam treba pomoć? Ovdje postavite svoje pitanje. Navedite jasan i sveobuhvatan opis problema i vašeg pitanja. Što više pojedinosti navedete za svoje pitanje i pitanje, lakše je drugim vlasnicima proizvoda VXS8 trgovačke marke Yamaha pravilno odgovoriti na vaše pitanje.
Informacije o Yamaha VXS8
Ovdje besplatno pogledajte priručnik za proizvod VXS8 trgovačke marke Yamaha. Ovaj je priručnik pod kategorijom , a ocijenio ga je sljedeći broj osoba: 1 prosječnom ocjenom od 7.5. Ovaj je priručnik dostupan na sljedećim jezicima: Engleski. Imate li pitanja u vezi s proizvodom VXS8 trgovačke marke Yamaha ili vam treba pomoć? Ovdje postavite svoje pitanje