Sony ZS-BT1

Sony ZS-BT1 priručnik

(1)
  • ZS-BT1US.3-099-777-21(1)
    WARNING
    To reduce the risk of re or electric shock,
    do not expose this apparatus to rain or
    moisture.
    To reduce the risk of re, do not cover the ventilation of
    the apparatus with newspapers, tablecloths, curtains, etc.
    And do not place lighted candles on the apparatus.
    To reduce the risk of re or electric shock, do not place
    objects lled with liquids, such as vases, on the apparatus.
    Connect the apparatus to an easily accessible AC
    outlet. Should you notice an abnormality in the
    apparatus, disconnect the main plug from the AC outlet
    immediately.
    Do not install the appliance in a conned space, such as a
    bookcase or built-in cabinet.
    3-099-777-21(1)
    Personal Audio System
    Operating Instructions
    US
    ZS-BT1
    © 2007 Sony Corporation Printed in China
    is symbol is intended to alert the
    user to the presence of uninsulated
    dangerous voltage” within the products
    enclosure that may be of sucient
    magnitude to constitute a risk of electric
    shock to persons.
    is symbol is intended to alert the user
    to the presence of important operating
    and maintenance (servicing) instructions
    in the literature accompanying the
    appliance.
    Power sources Specications
    AUDIO POWER SPECIFICATIONS
    POWER OUTPUT AND TOTAL HARMONIC DISTORTION
    With 3.2-ohm loads, both channels driven from 150 - 6 000 Hz; rated 1.8 W
    per channel-minimum RMS power, with no more than 10 % total harmonic
    distortion in AC operation.
    Other specications
    CD player section
    System
    Compact disc digital audio system
    Laser diode properties
    Emission duration: Continuous
    Laser output: Less than 44.6 µW
    (is output is the value measured at a distance of
    about 200 mm from the objective lens surface on the
    optical pick-up block with 7 mm aperture.)
    Number of channels
    2
    Frequency response
    20 - 20 000 Hz +1/–1 dB
    Wow and utter
    Below measurable limit
    Radio section
    Frequency range
    FM: 87.5 - 108 MHz
    AM: 530 - 1 710 kHz
    Antennas
    FM: Telescopic antenna
    AM: Built-in ferrite bar antenna
    General
    Speaker
    Full range: 10 cm (4 in.) dia., 3.2 , cone type (2)
    Input
    AUDIO IN jack (stereo minijack): Minimum input level 245 mV
    Outputs
    Headphones jack (stereo minijack)
    For 16 - 64 impedance headphones
    Power output
    2.3 W + 2.3 W (at 3.2 , 10% harmonic distortion)
    Power requirements
    For player:
    120 V AC, 60 Hz
    9 V DC, 6 R20 (size D) batteries
    For remote control:
    3 V DC, 2 R06 (size AA) batteries
    Power consumption
    AC 14 W
    Bluetooth section
    Communication system:
    Bluetooth Standard version 2.0
    Output:
    Bluetooth Standard Power Class 2
    Maximum communication range:
    Line of sight approx. 10 m
    1)
    Frequency band:
    2.4 GHz band (2.4000 GHz - 2.4835 GHz)
    Modulation method:
    FHSS
    Compatible Bluetooth proles
    2)
    :
    A2DP (Advanced Audio Distribution Prole)
    AVRCP (Audio Video Remote Control Prole)
    Supported codecs:
    Receive: SBC (Sub Band Codec), MP3
    Transmit: SBC (Sub Band Codec)
    1)
    e actual range will vary depending on factors such as obstacles between
    devices, magnetic elds around a microwave oven, static electricity,
    reception sensitivity, antennas performance, operating system, soware
    application, etc.
    2)
    Bluetooth standard proles indicate the purpose of Bluetooth
    communication between devices.
    Battery life
    For player:
    FM Radio reception
    Sony R20P: approx. 15 h
    Sony alkaline LR20: approx. 36 h
    CD playback
    Sony R20P: approx. 5 h
    Sony alkaline LR20: approx. 14 h
    It is recommended that you use alkaline batteries.
    Dimensions
    Approx. 480 × 156 × 250 mm (w/h/d)
    (19 × 6
    1
    /4 × 9
    7
    /
    8
    inches) (incl. projecting parts)
    Mass
    Approx. 4.3 kg (9 lb. 8 oz) (incl. batteries)
    Supplied accessories
    AC power cord (1)
    Remote control (1)
    Design and specications are subject to change without notice.
    Optional accessories
    Sony MDR headphones series
    Basic Operations
    * VOLUME +
    and
    on the unit have a tactile dot.
    Before using the unit
    To turn on/o the power
    Press POWER
    .
    To adjust the volume
    Press VOLUME +, –
    .
    To listen through headphones
    Connect the headphones to the (headphones) jack .
    To select the sound characteristic
    Press SOUND
    repeatedly to select the audio emphasis
    you want.
    Choose To get
    Powerful, clean sounds, emphasizing low and
    high range audio
    Light, bright sounds emphasizing high and
    middle range audio
    Percussive sounds, emphasizing bass audio
    The presence of vocals, stressing middle
    range audio
    The whole dynamic range for music such as
    classical music
    To reinforce the bass sound
    Press MEGA BASS
    to display “MEGA BASS” in the
    display.
    To return to normal sound, press MEGA BASS
    to
    disappear from the display.
    Note
    MEGA BASS does not function when you use the Bluetooth
    headphones to listen to a sound source other than through the
    Bluetooth function (e.g., CD, radio, or AUDIO IN).
    Playing a CD
    1 Press CD
    on the unit.
    CD” appears in the display.
    2 Press
    on the unit, and place a disc with the
    label side up on the CD tray.
    To close the CD tray, press
    on the unit.
    3 Press
    on the unit.
    e unit plays all the tracks once.
    Track number Playing time
    To Press
    Pause playback
    . To resume play, press it again.
    Stop playback
    .
    Go to the next track
    ( on the remote) .
    Go back to the
    previous track
    ( on the remote) .
    Locate a point while
    listening to the sound
    (forward) or
    (backward) while playing and hold it
    until you find the point. (On the remote,
    use or )
    Locate a point while
    observing the display
    (forward) or
    (backward) in pause and hold it until
    you find the point. (On the remote, use
    or )
    Remove the CD
    .
    On the remote
    To select CD function, press CD
    .
    Notes
    When pressing
    (
    ,
    , , ) on the unit, press
    the marking at the part near the outer edge.
    You cannot locate a specic track if “SHUF” or “PGM” is lit in the
    display. Press
    , and then press MODE
    repeatedly until
    “SHUF” and “PGM” disappears from the display.
    Listening to the radio
    To listen to FM or AM
    1 Press RADIO BAND
    AUTO PRESET
    on the unit
    (RADIO
    BAND
    on the remote) repeatedly to
    select FM or AM.
    2 Hold down TUNE + or –
    until the frequency digits
    begin to change in the display.
    e unit automatically scans the radio frequencies and
    stops when it nds a clear station.
    If you cannot tune in a station, press TUNE + or –
    repeatedly to change the frequency step by step.
    When an FM stereo broadcast is received, “ST
    appears.
    Tip
    If the FM broadcast is noisy, press MODE
    until “MONO” appears
    in the display and the radio will play in monaural.
    Using the Bluetooth function
    is unit supports Bluetooth A2DP and AVRCP proles.
    For details on Bluetooth wireless technology, see
    “Bluetooth wireless technology” on the back page.
    Check the websites below for the latest information about
    compatible devices.
    <http://www.sony.com/support>
    Listening to music of a Bluetooth mobile
    phone or Bluetooth device
    You can listen to music from your Bluetooth mobile
    phone or Bluetooth device over a wireless connection.
    Follow the procedure below to listen to music from
    Bluetooth devices with this unit.
    Pairing this unit with a Bluetooth device
    Connecting to registered devices
    Playing music of a Bluetooth device
    For details about the operations of the Bluetooth device,
    also refer to the operation manual supplied with your
    Bluetooth device.
    Pairing this unit with a Bluetooth device
    Pairing is an operation where Bluetooth devices register
    with each other beforehand. Use the procedure below to
    pair the unit with your Bluetooth device. Once a pairing
    operation is performed, it does not need to be performed
    again. If pairing is already completed, proceed to “Playing
    music of a Bluetooth device” on this page.
    1 Place the Bluetooth device to be connected to this
    unit within 1 meter of the unit.
    2 Press BLUETOOTH
    .
    3 Operate the Bluetooth device and perform the
    pairing operation.
    For details about the operations of the Bluetooth
    device, refer to the operation manual supplied with
    your Bluetooth device.
    When establishing a connection with this unit, select
    the audio prole (A2DP, AVRCP) at the Bluetooth
    device. If the Bluetooth device does not support the
    AVRCP prole, you cannot perform playback or other
    operations with the unit (See “Playing music on this
    unit” on the back page).
    4 Enter the passcode.
    Passcode entry may be required depending on the
    type of Bluetooth device.
    When “PIN” appears, enter the passcode at the unit
    as follows:
    Press
    ,
    , , on the unit (
    –,
    + and
    
    ,
    
    on the remote)
    to enter the same passcode that was entered at the
    Bluetooth device, and then press ENTER
    . Use
    and
    (
    
    and
    
    ) to
    select the digit, and and (
    – and
    +) to
    change the value.
    Once pairing is completed and the connection is
    established, the unit display changes as follows:
    “LINKED Name of the Bluetooth device
    To cancel passcode entry partway
    Press
    .
    Notes
    “Passcode” may be called “Passkey”, “PIN code, “PIN number” or
    “Password”, etc. depending on the device.
    is unit only supports numerical passcodes up to 4 digits.
    e pairing standby status of the unit is cancelled aer about 30
    seconds. If pairing is not successful, redo the procedure from step 1.
    While connected to a Bluetooth device, this unit cannot be detected
    and a connection cannot be established from another Bluetooth
    device.
    To erase all the pairing registration information
    1 Press BLUETOOTH
    .
    When the unit is connected with a Bluetooth
    device (when the Bluetooth device name or other
    information appears in the unit display), press and
    hold BLUETOOTH OPR
    on the unit for about 2
    seconds to put the unit in Bluetooth standby mode.
    2 Press CLEAR
    on the remote.
    “DELETE” appears.
    3 Press ENTER
    .
    COMPLETE” appears and all the pairing information
    is erased.
    Note
    In order to connect with a Bluetooth device aer performing this
    operation, you must enter the passcode again.
    Playing music of a Bluetooth device
    You can operate a Bluetooth device by connecting the
    unit and a Bluetooth device using AVRCP. If the unit is
    not connected with a Bluetooth device using AVRCP,
    “NOT USED” appears when you operate the unit.
    1 Press BLUETOOTH
    .
    2 Establish a connection from the Bluetooth device.
    For details about the operations of the Bluetooth
    device, refer to the operation manual supplied with
    your Bluetooth device.
    Once the connection is established, the unit display
    changes as follows:
    “LINKED Name of the Bluetooth device
    3 Press
    .
    Depending on the Bluetooth device, you may need
    to start up the AV soware of the Bluetooth device
    beforehand.
    4 Press VOLUME + or – to adjust the volume
    .
    To check the address of a connected Bluetooth
    device
    Press DISPLAY
    while the Bluetooth device name
    appears in the unit display.
    e Bluetooth device address appears.
    To cancel the connection with a Bluetooth
    device
    Press and hold BLUETOOTH OPR
    on the unit for
    about 2 seconds until “UNLINKED” appears, or until
    the information on the display (device name, etc.)
    disappears.
    Other operation
    To Press
    Pause playback
    .
    Stop playback
    .
    Select a file
    / on the unit
    (/ on the remote) .
    Find a point in a file
    Hold down / on the
    unit (/ on the remote) .
    Note
    ese operations may not be available for certain Bluetooth devices.
    In addition, the actual operations may dier depending on the
    connected Bluetooth device.
    Notes on connections with Bluetooth devices
    If you cannot connect with a paired Bluetooth device,
    perform the pairing operation between the unit and the
    Bluetooth device again.
    Depending on the type of Bluetooth device, you can
    adjust the volume using the controls of the Bluetooth
    device.
    When BLUETOOTH
    is pressed while connected to
    Bluetooth headphones, it may take some time until a
    connection is made to the unit from another Bluetooth
    device.
    Preparing the remote
    Insert two R6 (size AA) batteries (not supplied).
    Replacing batteries
    With normal use, the batteries should last for about six months. When the remote no longer operates the unit, replace all
    the batteries with new ones.
    Connect the AC power cord or insert six R20 (size D) batteries (not supplied) into the battery compartment .
    Notes
    Replace the batteries when the OPR/BATT indicator
    dims or when the unit stops operating.
    Replace all the batteries with new ones. Before you replace the batteries, be sure to take out the CD from the unit.
    To use the unit on batteries, disconnect the AC power cord from the unit.
    When you operate the unit on batteries, you cannot turn on the unit using the remote.
    2 to a wall
    outlet
    1 to AC IN
    Listening to music on this unit using
    Bluetooth headphones
    You can listen to music played on this unit using your
    Bluetooth headphones over a wireless connection.
    Follow the procedure below to listen to music on this
    unit with Bluetooth headphones.
    Pairing this unit with Bluetooth headphones
    Connecting to registered headphones
    Playing music on this unit
    For details about the operations of the Bluetooth
    headphones, also refer to the operation manual supplied
    with your Bluetooth headphones.
    Pairing this unit with Bluetooth headphones
    Pairing is an operation where Bluetooth devices register
    with each other beforehand. Use the procedure below
    to pair the unit with your Bluetooth headphones. Once
    a pairing operation is performed, it does not need to be
    performed again. If pairing is already completed, proceed
    to “Playing music on this unit” on the back page.
    1 Select a function other than the Bluetooth function.
    2 Place the Bluetooth headphones to be connected to
    this unit within 1 meter of the unit.
    3 Put the Bluetooth headphones in pairing mode.
    For details about the operations of the Bluetooth
    headphones, refer to the operation manual supplied
    with your Bluetooth headphones.
    4 Press and hold BLUETOOTH OPR
    on the unit for
    about 7 seconds until the BLUETOOTH indicator
    ashes.
    Sound output from the speakers is stopped.
    5 Enter the passcode.
    Follow the same procedure as in step 4 of “Pairing this
    unit with a Bluetooth device” on this page.
    Once pairing is completed and the connection is
    established, the unit display changes as follows:
    “LINKED Name of the Bluetooth device
    To cancel passcode entry partway
    Press
    .
    Notes
    “Passcode” may be called “Passkey”, “PIN code, “PIN number” or
    “Password”, etc. depending on the device.
    is unit only supports numerical passcodes up to 4 digits.
    e pairing standby status of the unit is cancelled aer about 30
    seconds. If pairing is not successful, redo the procedure from step 1.
    While connected to a Bluetooth device, this unit cannot be detected
    and a connection cannot be established from another Bluetooth
    device.
    Pairing may not be possible if other Bluetooth devices are present
    around the unit. In this case, turn o the other Bluetooth devices.
    To erase all the pairing registration information
    1 Press BLUETOOTH
    .
    When the unit is connected with a Bluetooth
    device (when the Bluetooth device name or other
    information appears in the unit display), press and
    hold BLUETOOTH OPR
    on the unit for about 2
    seconds to put the unit in Bluetooth standby mode.
    2 Press CLEAR
    on the remote.
    “DELETE” appears.
    3 Press ENTER
    .
    COMPLETE” appears and all the pairing information
    is erased.
    Note
    To connect with Bluetooth headphones aer performing this
    operation, you must enter the passcode again.
    Continued on back page
    CAUTION
    e use of optical instruments with this product will
    increase eye hazard.
    Information
    For customers in the USA
    is equipment has been tested and found to comply
    with the limits for a Class B digital device, pursuant
    to Part 15 of the FCC Rules. ese limits are designed
    to provide reasonable protection against harmful
    interference in a residential installation. is equipment
    generates, uses and can radiate radio frequency energy
    and, if not installed and used in accordance with the
    instructions, may cause harmful interference to radio
    communications. However, there is no guarantee that
    interference will not occur in a particular installation. If
    this equipment does cause harmful interference to radio
    or television reception, which can be determined by
    turning the equipment o and on, the user is encouraged
    to try to correct the interference by one or more of the
    following measures:
    Reorient or relocate the receiving antenna.
    Increase the separation between the equipment and
    receiver.
    Connect the equipment into an outlet on a circuit
    dierent from that to which the receiver is connected.
    Consult the dealer or an experienced radio/TV
    technician for help.
    You are cautioned that any changes or modications
    not expressly approved in this manual could void your
    authority to operate this equipment.
    is equipment must not be co-located or operated in
    conjunction with any other antenna or transmitter.
    is equipment complies with FCC radiation exposure
    limits set forth for uncontrolled equipment and meets
    the FCC radio frequency (RF) Exposure Guidelines in
    Supplement C to OET65.
    is equipment has very low levels of RF energy that
    it deemed to comply without maximum permissive
    exposure evaluation (MPE). But it is desirable that it
    should be installed and operated with at least 20cm and
    more between the radiator and persons body (excluding
    extremities: hands, wrists, feet and legs).
    Notes on DualDiscs
    A DualDisc is a two sided disc product which mates
    DVD recorded material on one side with digital
    audio material on the other side. However, since the
    audio material side does not conform to the Compact
    Disc (CD) standard, playback on this product is not
    guaranteed.
    Owners Record
    e model number is located at the bottom and the serial number is located in the battery compartment.
    Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer
    regarding this product.
    Model No. Serial No.
    Music discs encoded with copyright
    protection technologies
    is product is designed to playback discs that conform
    to the Compact Disc (CD) standard. Recently, various
    music discs encoded with copyright protection
    technologies are marketed by some record companies.
    Please be aware that among those discs, there are some
    that do not conform to the CD standard and may not be
    playable by this product.
    For customers in the USA
    Please register this product on line at
    http://www.sony.com/productregistration
    Proper registration will enable us to send you periodic
    mailings about new product, services and other
    important announcements. Registering your product
    will also allow us to contact you in the unlikely event
    that the product needs adjustment or modication.
    ank you.
    e Bluetooth word mark and logos are owned by the
    Bluetooth SIG, Inc. and any use of such marks by Sony
    Corporation is under license. Other trademarks and
    trade names are those of their respective owners.
    TM and (R) marks are omitted in this manual.
    MPEG Layer-3 audio coding technology and patents
    licensed from Fraunhofer IIS and omson.

Trebate pomoć?

Broj pitanja: 0

Imate li pitanja u vezi s proizvodom ZS-BT1 trgovačke marke Sony ili vam treba pomoć? Ovdje postavite svoje pitanje. Navedite jasan i sveobuhvatan opis problema i vašeg pitanja. Što više pojedinosti navedete za svoje pitanje i pitanje, lakše je drugim vlasnicima proizvoda ZS-BT1 trgovačke marke Sony pravilno odgovoriti na vaše pitanje.

Ovdje besplatno pogledajte priručnik za proizvod ZS-BT1 trgovačke marke Sony. Ovaj je priručnik pod kategorijom , a ocijenio ga je sljedeći broj osoba: 1 prosječnom ocjenom od 7.5. Ovaj je priručnik dostupan na sljedećim jezicima: Engleski. Imate li pitanja u vezi s proizvodom ZS-BT1 trgovačke marke Sony ili vam treba pomoć?

Značajke proizvoda ZS-BT1 trgovačke marke Sony

Brend Sony
Model ZS-BT1
Proizvod Hi-Fi sustav
Jezik Engleski
Vrsta datoteke PDF

Srodni proizvodi proizvodu ZS-BT1 trgovačke marke Sony

    Povezani priručnici za proizvode

    Hi-Fi sustav Sony

    Dodaj priručnik

    Imate li priručnik koji želite dodati?