Siemens WM12S421EE

Siemens WM12S421EE priručnik

(1)
  • 1
    Safety instructions
    The washing machine is heavy - take care when lifting.
    Caution: frozen hoses can crack/burst. Do not install the washing machine outdoors or
    in areas exposed to frost.
    The washing machine could be damaged. Do not lift the appliance by protruding
    components (e.g. the washing machine door).
    In addition to the instructions provided in this document, special regulations from the
    relevant water and electric utility companies may apply.
    If in doubt, have a technician connect the appliance.
    Route hoses and cables in such a way that there is no risk of tripping.
    Environmentally-friendly disposal
    Dispose of packaging in an environmentally friendly manner.
    This appliance is labelled in accordance with European Directive 2002/96/EC on
    Waste Electrical and Electronic Equipment - WEEE.
    The directive provides an EU-wide framework for the return and recycling of used
    appliances.
    Installation surface
    The machine must be stable so that it does not move around.
    The surface on which it is installed must be firm and level.
    Soft floors/floor coverings are not suitable.
    Installation on a pedestal
    The feet of the washing machine must be secured with holding brackets *.
    * Order no. WMZ 2200, WX 9756, CZ 110600, Z 7080X0
    Installation on a wood joist floor
    If possible, place the washing machine in a corner.
    Screw a water-resistant wooden board (min. 30 mm thick) to the floor.
    The feet of the washing machine must be secured with holding brackets *.
    * See above for order no.
    Installing the appliance depending on model
    Install the appliance before connecting it to the power supply.
    Risk of electric shock.
    For models with a continuous appliance covering plate or a square service flap, the
    appliance covering plate can be replaced by a metal cover.
    Instead of the appliance covering plate, you must have a metal cover * fitted by an expert.
    * Order no. WMZ 2043, WZ 20430
    For models with a non-continuous appliance covering plate or a round service flap, the
    appliance covering plate must not be removed.
    Only install the washing machine underneath a continuous worktop that is securely
    connected to adjacent cabinets.
    Recess width of 60 cm required.
    2
    Scope of delivery depending on model
    Also required, depending on the connection:
    1 hose clamp Ø 24-40 mm (specialist retailers) to connect to a siphon
    a Page 4; water connection
    Useful tools
    Spirit level for levelling.
    Spanner with
    WAF13: for loosening the transport safety devices a Page 3 and
    WAF17: for aligning the appliance feet a Page 5.
    Hose and cable lengths depending on model
    Left-hand connection
    or
    Right-hand connection
    Note: Using hose clips limits the possible hose lengths.
    Available from specialist retailers/the after-sales service:
    Extension for AquaäStop and cold water inlet hose (approx. 2.50 m).
    Order no. WMZ2380, WZ10130, CZ11350, Z7070X0
    Longer inlet hose (approx. 2.20 m) for standard model.
    Spanner
    Mains cable
    Water inlet
    Elbow
    for fixing the drainage
    hose in place
    Covers
    with hose clip
    AquaäStop AquaäSecure/Standard
    Water outlet
    ~
    140 cm
    ~
    95 cm
    ~
    120 cm
    ~
    130 cm
    ~
    100 cm
    ~
    135 cm
    0 - max. 100 cm
    Moisture inside the drum is
    due to final testing.
    3
    Removing the transport safety devices
    Before using the appliance for the first time, the 4 transport safety
    devices must be completely removed and kept safe.
    If you need to transport the appliance at a later date, always refit the
    transport safety devices to prevent damage to the machine.
    a Page 6.
    Store the screw and sleeve screwed together.
    1. Take the hoses (depending on model) out of the holders and the elbow.
    Remove the elbow.
    2. Unscrew and remove the bolts from all 4 transport safety devices.
    3. Take the mains cable out of the holder. Remove the sleeves.
    4. Insert the covers. Secure tightly by pressing on the snap-in hook. Insert the hose clip.
    5. Secure the hoses in the hose clips.
    4
    Water connection depending on model
    Risk of electric shock. Do not immerse the Aqua-Stop safety device in water
    (contains an electric valve).
    To prevent leaks or water damage, observe the instructions in this section.
    Caution: only operate the washing machine using cold drinking water.
    Do not connect to the mixer tap of an unpressurised hot-water boiler.
    Do not use a used inlet hose. Only use the inlet hose supplied or one which was
    purchased from an authorised specialist retailer.
    If in doubt, have a technician connect the appliance.
    Water inlet
    Water inlet hose:
    Caution: do not kink, squash, modify or cut through
    (otherwise its strength is no longer guaranteed).
    Optimum water pressure in the supply network: 100-1000 kPa (1-10 bar)
    When the tap is on, the water flow is at least 8 l/min.
    If the water pressure is higher than this, a pressure reducing valve must be installed.
    Model: AquaäStop
    AquaäSecure
    Standard
    1. Connect the water inlet hose to the tap.
    Caution: only tighten the screw connections by
    hand.
    2. Open the water tap carefully, checking the leak
    tightness of the connection points.
    Caution: the screw connection is under mains
    water pressure.
    Water outlet
    Water outlet hose:
    Caution: do not kink or pull lengthways.
    Height difference between the installation surface and the drain:
    0 - max. 100 cm
    Outlet into a sink
    Caution: secure the drain hose so that it cannot slip out.
    Caution: the plug must not block drainage from the sink. During pumping,
    check whether the water is draining away quickly enough. The end of the
    drain hose must not be immersed in the water that is pumped out! This
    would result in the risk of water being sucked back into the washing
    machine!
    Drainage into a siphon:
    Caution: the connection point must be secured with a hose clamp,
    Ø 24-40 mm (specialist retailers).
    .
    Outlet into a plastic pipe with rubber bushing or into a drainage pit:
    Caution: secure the drain hose so that it cannot slip out.
    max.
    90°
    max.
    90°
    min.
    10 mm
    min.
    10 mm
    3/4
    3/4
Siemens WM12S421EE

Trebate pomoć?

Broj pitanja: 0

Imate li pitanja u vezi s proizvodom WM12S421EE trgovačke marke Siemens ili vam treba pomoć? Ovdje postavite svoje pitanje. Navedite jasan i sveobuhvatan opis problema i vašeg pitanja. Što više pojedinosti navedete za svoje pitanje i pitanje, lakše je drugim vlasnicima proizvoda WM12S421EE trgovačke marke Siemens pravilno odgovoriti na vaše pitanje.

Ovdje besplatno pogledajte priručnik za proizvod WM12S421EE trgovačke marke Siemens. Ovaj je priručnik pod kategorijom , a ocijenio ga je sljedeći broj osoba: 1 prosječnom ocjenom od 8.1. Ovaj je priručnik dostupan na sljedećim jezicima: Engleski. Imate li pitanja u vezi s proizvodom WM12S421EE trgovačke marke Siemens ili vam treba pomoć? Ovdje postavite svoje pitanje

Značajke proizvoda WM12S421EE trgovačke marke Siemens

Brend Siemens
Model WM12S421EE
Proizvod Perilica rublja
EAN 4242003540183
Jezik Engleski
Vrsta datoteke PDF
Napajanje
Razred energetske učinkovitosti A+++
Potrošnja struje prilikom pranja 1.03kWh
Potrošnja vode po ciklusu 56L
Struja 10A
Godišnja potrošnja energije - pranje 189kWh
Godišnja potrošnja vode za pranje 10500L
Potrošnja električne energije (maks) 2300W
Ulazni napon izmjenične struje 220-240V
Ulazna frekvencija izmjenične struje 50Hz
Energy Star certifikat -
Dizajn
Ugrađen zaslon
Vrsta zaslona LED
Tip utovara Prednje punjenje
Tip Samostojeći (odvojen)
Duljina kabela 1.75m
Šarke vrata Left
Zapremina bubnja 65L
Tehnologija izravnog pogona (invertera)
Certifikacija CE, VDE
Materijal bubnja Nehrđajući čelik
Materijal kućišta Plastika
Tip kontrole Buttons, Rotary
Boja proizvoda Bijelo
Vrata u boji Bijelo
Učinak
Klasa pranja A
Broj programa za pranje -
Kapacitet bubnja 8kg
Maksimalna brzina centrifuge 1200RPM
Razred centrifugalnog sušenja B
Trajanje ciklusa (maks.) 205min
Sustav kontrole pjene
Tajmer za odgodu uključivanja
Sustav ujednačavanja opterećenja
Odgođeni početak 24h
Podesiva brzina rotacije
Ergonomija
Zaštita djece
Samočišćenje
Podesive noge
Podešavanje nožica 12mm
Preostalo vrijeme pokazatelj
- Black, Blouse/shirt, Cotton, Microfibre, Mix, Pre-wash, Quick, Synthetics
Težina i dimenzije
Širina 600mm
Dubina 590mm
Visina 842mm
Težina 76000g
Dubina s otvorenim vratima 990mm
Programi pranja
Program pranja za alergičare
Program pranja za crnu odjeću
Program pranja za bluze/košulje
Program pranja pamuka
Program pranja mikrofibre
Program miješanog pranja
Program pretpranja
Program brzog pranja
Program pranja sintetike

Povezani priručnici za proizvode

Perilica rublja Siemens

prirucnici.hr

Tražite priručnik? prirucnici.hr osigurava da u trenu pronađete priručnik koji tražite. Naša baza podataka sadrži više od milijun PDF priručnika za više od 10,000 robnih marki. Svaki dan dodajemo najnovije priručnike pa ćete uvijek pronaći proizvod koji tražite. Vrlo je jednostavno: samo u tražilicu upišite naziv robne marke i vrstu proizvoda i odmah ćete vidjeti priručnik po svom izboru na Internetu, besplatno.

prirucnici.hr

© Autorska prava 2020 prirucnici.hr. Sva prava pridržana.