NEC 100012721

NEC 100012721 priručnik

(1)
  • english
    SINGLE BOARD COMPUTER
    Quick Reference Guide / Kurzübersicht / Guide de référence rapide
    INSTALLATION INSTRUCTIONS
    1) Switch the display off completely using the hard on/off switch or disconnect the equipment fully
    from the mains.
    2) The computer must be placed in the plug-in slot designed for this purpose. This is located on the
    left hand side of the display near the carrying handle.
    3) Remove the carrying handle by loosening the two Phillips-head screws.
    4) Remove the cover panel over the plug-in slot by loosening the two Phillips-head screws.
    5) Ensure that the computer is inserted with the right orientation. This is correct when the USB ports
    and the LAN port are on top and the computer’s heat sink is facing the front of the display.
    Slide the computer carefully into the plug-in slot, until you feel it lock into place. Do not force it in!
    6) Now use the screws that were previously holding the cover panel in place to secure the computer.
    7) Re-attach the carrying handle. Ensure that the screws are properly tightened (1.39 – 1.89 Nm torque).
    Risk of an accident!
    8) In the Display menu, go to „Display protection“ / „Fan control“ and switch fans to „on“.
    This is important specifi cally to prevent the hard disk from overheating.
    9) The computer is supplied as standard with a resolution of 1360 x 768. If using the computer in
    a NEC MULTEOS or NEC MultiSync
    ®
    LCD6520, please set the resolution accordingly (1920 x 1080).
    10) The computer must not be operated at the same time as the internal amplifi er. The display may be
    damaged (in newer displays the audio function is automatically deactivated).
    11) NEC Display Solutions GmbH assumes no liability for loss of data and resulting losses/damage.
    OPERATING AND MAINTENANCE INSTRUCTIONS
    1) Please note that the combination of computer and display is approved up to a maximum ambient
    temperature of 35°. Higher temperatures may cause damage to the display and computer or reduce
    their usable life.
    2) Should you wish to remove the computer from the plug-in slot, ensure that the computer has cooled
    down suffi ciently. Parts of the computer can reach temperatures of above 100° Celsius. Risk of burns!
    3) The computer must not be opened either for maintenance or to expand or replace the memory.
    Opening the computer will invalidate the guarantee.
    4) All dust should be removed from the computer (and, where applicable, the display) regularly
    (e.g. every 6 or 12 months). How often cleaning is required depends largely on the operating hours,
    the ambient temperature and the amount of dust in the surroundings. A brush, for example, can be
    used for cleaning, to remove dust from the fan and the cooling fi ns. Never open the computer housing!
    5) Do not change the BIOS settings, which reduce the clock frequency of the CPU in the event of
    overheating.
    TROUBLESHOOTING
    1) The computer does not start.
    a. Is the computer correctly positioned in the plug in slot and have the screws been tightened?
    b. It is possible that the BIOS settings have been changed so that the computer only starts when
    the on/off switch is pressed. Press the on/off switch or reset the original BIOS confi guration.
    2) The computer starts but there is no picture on the display.
    a. Have you selected “Computer“ as the input?
    b. If you have connected an external display, the internal display may have been deactivated.
    Re-connect the external display and confi gure the monitor controls under “Display” so that the
    internal display is the primary one.
    c. If you have changed the BIOS settings, this may also cause the effect described in 2) b. Reset
    the original BIOS confi guration.
    3) The picture is out of focus.
    a. Has the correct resolution been set?
    i. NEC MultiSync
    ®
    LCD4020, LCD4620: 1360 x 768
    ii. NEC MULTEOS
    ®
    M40, M46 and MultiSync
    ®
    LCD6520: 1920 x 1080
    b. The display has possibly been set up for a different size. Press the “Size” button on the remote
    control until “standard” is displayed in green in the top right hand side of the screen.
    4) The system is slow and even unstable after software has been installed / uninstalled.
    a. The operating system is restricted by the software and/or residual software in terms of
    operation and performance. Reinstall the operating system using the enclosed “Recovery” DVD.
    Note 1: All stored data will be lost!
    Note 2: The initial boot process after reinstallation can take up to 15 minutes.
    5) A device that has been connected using USB or an ExpressCard, does not operate correctly.
    a. Ensure that all the drivers have been installed.
    b. Contact the manufacturer of the USB / ExpressCard device.
    c. Reinstall the operating system using the enclosed Recovery DVD.
    Note 1: All stored data will be lost!
    Note 2: The initial boot process after reinstallation can take up to 15 minutes.
    6) The display’s speakers are silent even though I am outputting audio.
    a. This is normal. The internal speaker does not work in combination with the computer. The audio
    signal can only be picked up from the display’s 3.5mm jack socket.
    7) RS232 communication with the display is not working.
    a. You have a display with old fi rmware. Please contact NEC Display Solutions GmbH to obtain a
    rmware upgrade.
    INSTALLATIONSHINWEISE:
    1) Schalten Sie das Display über den Kippschalter vollständig aus oder trennen Sie das Gerät
    vollständig vom Netz.
    2) Der Rechner muss in den dafür vorgesehen Einschubschacht eingesetzt werden. Dieser befi ndet
    sich auf der linken Seite des Displays in der Nähe des Tragegriffs.
    3) Entfernen Sie den Tragegriff, in dem Sie die beiden Kreuzschrauben lösen.
    4) Entfernen Sie die Abdeckplatte, die den Einschubschacht verschließt, in dem Sie die beiden
    Kreuzschrauben lösen.
    5) Stellen Sie sicher, dass die Option in der richtigen Orientierung eingeführt wird. Diese ist richtig, wenn
    sich die USB-Anschlüsse und der LAN-Anschluss oben befi nden und der Kühlkörper des Rechners in
    Richtung Vorderseite des Displays zeigt. Führen Sie die Option vorsichtig in den Einschubschacht ein,
    bis ein Einrasten zu spüren ist. Wenden Sie keine Gewalt an!
    6) Benutzen Sie nun die Schrauben, mit denen zuvor die Abdeckplatte befestigt war, um den Rechner zu
    xieren.
    7) Befestigen Sie wieder den Haltegriff. Stellen Sie sicher, dass die Schrauben korrekt angezogen sind
    (1,39 – 1,89 Nm Drehmoment)! Unfallgefahr!
    8) Stellen Sie im Menü des Displays unter „Monitorschutz“/ „Ventilatorensteuerung“ die Display-
    Lüfter auf „ein“. Dies ist notwendig, um speziell eine Überhitzung der Festplatte zu vermeiden.
    9) Der Rechner wird standardmäßig mit einer Aufl ösung von 1360 x 768 geliefert. Wenn Sie den
    Rechner in einem NEC MULTEOS oder NEC MultiSync
    ®
    LCD6520 betreiben, passen Sie bitte die
    Aufl ösung an (1920 x 1080).
    10) Der Rechner darf nicht gleichzeitig mit dem internen Verstärker betrieben werden. Das Display kann
    beschädigt werden (bei neueren Displays ist die Audiofunktion automatisch deaktiviert).
    11) Für Datenverluste und daraus resultierende Schäden übernimmt NEC Display Solutions GmbH keine
    Haftung.
    deutsch
    Ethernet
    }
    USB DVI-I out
    ExpressCard
    ResetPowerLED / Button
NEC 100012721

Trebate pomoć?

Broj pitanja: 0

Imate li pitanja u vezi s proizvodom 100012721 trgovačke marke NEC ili vam treba pomoć? Ovdje postavite svoje pitanje. Navedite jasan i sveobuhvatan opis problema i vašeg pitanja. Što više pojedinosti navedete za svoje pitanje i pitanje, lakše je drugim vlasnicima proizvoda 100012721 trgovačke marke NEC pravilno odgovoriti na vaše pitanje.

Ovdje besplatno pogledajte priručnik za proizvod 100012721 trgovačke marke NEC. Ovaj je priručnik pod kategorijom , a ocijenio ga je sljedeći broj osoba: 1 prosječnom ocjenom od 9.1. Ovaj je priručnik dostupan na sljedećim jezicima: Engleski, Njemački, Francuski. Imate li pitanja u vezi s proizvodom 100012721 trgovačke marke NEC ili vam treba pomoć?

Značajke proizvoda 100012721 trgovačke marke NEC

Brend NEC
Model 100012721
Proizvod Stolno računalo
EAN 3540260050478
Jezik Engleski, Njemački, Francuski
Vrsta datoteke PDF
Procesor
Frekvencija procesora 1.2GHz
Model procesora -
Porodica procesora Intel® Celeron®
Čipset matične ploče -
Memorija
Interna memorija 2GB
Zaslon
Zaslon priložen
Ostale značajke
Mogućnosti mreže Gigabit Ethernet
Kompatibilni operacijski sustavi Windows XPe
Linux
LED rada
Verzija operativnog sustava -
Priključci i sučelja
Broj Ethernet LAN (RJ-45) priključaka 1
Broj USB 2.0 priključaka 3
Broj DVI-I priključaka 1
Izlazi za slušalice 1
Težina i dimenzije
Težina 1600g
Napajanje
Napajanje 23W
Radni uvjeti
Raspon radne temperature (T-T) 5 - 35°C
Dizajn
Boja proizvoda Cr✗
Pohrana
Integriran čitač kartica
Ukupni prostor za pohranu 250GB
Softver
Instalirani operacijski sustav Windows XPe

Povezani priručnici za proizvode

Stolno računalo NEC