Motorola MT352TPR

Motorola MT352TPR priručnik

(1)
  • MT Series
    KEM-ML34301
    Safety and General Information
    I
    mportant Information on Safe and Efficient Operation
    Read This Information Before Using Your Radio.
    The information provided in this document supersedes the general safety
    information in user guides published prior to December 1, 2002.
    Transmit and Receive Procedure
    Your two-way radio contains a transmitter and a receiver. To control your
    exposure and ensure compliance with the general population/
    uncontrolled environment exposure limits, always adhere to the following
    procedure:
    Transmit no more than 50% of the time.
    To receive calls, release the PTT button.
    To transmit (talk), press the Push to Talk (PTT) button.
    Transmitting 50% of the time, or less, is important because the radio
    generates measurable RF energy exposure only when transmitting (in
    terms of measuring standards compliance).
    Exposure to Radio Frequency Energy
    Your Motorola two-way radio complies with the following RF energy
    exposure standards and guidelines:
    United States Federal Communications Commission, Code of Federal
    Regulations; 47CFR part 2 sub-part J.
    American National Standards Institute (ANSI)/Institute of Electrical
    and Electronic Engineers (IEEE) C95. 1-1992.
    Institute of Electrical and Electronics Engineers (IEEE) C95.
    1-1999 Edition.
    International Commission on Non-Ionizing Radiation Protection
    (ICNIRP) 1998.
    Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure
    to Radiofrequency Electromagnetic Fields in the Frequency Range
    from 3 KHz to 300 GHz, 1999.
    Australian Communications Authority Radiocommunications
    (Electromagnetic Radiation—Human Exposure) Standard, 2003.
    ANATEL ANNEX to Resolution No. 303 of July 2, 2002.
    ANATEL ANNEX to Resolution No. 533 of September 10, 2009.
    To ensure optimal radio performance and make sure human exposure to
    radio frequency electromagnetic energy is within the guidelines set forth
    in the above standards, always adhere to the following procedures.
    Portable Radio Operation and EME Exposure
    Antenna Care
    Use only the supplied or an approved replacement antenna.
    Unauthorized antennas, modifications, or attachments could damage the
    radio and may violate FCC regulations.
    Do NOT hold the antenna when the radio is “IN USE.” Holding the
    antenna affects its effective range.
    B
    ody-Worn Operation
    T
    o maintain compliances with FCC/Health Canada RF exposure
    g
    uidelines if you wear a radio on your body when transmitting always
    p
    lace the radio in a Motorola-supplied or approved clip holder, holster,
    case or body harness for this product. Use of non-Motorola-approved
    accessories may exceed FCC/Health Canada RF exposure guidelines.
    If you do not use one of the Motorola-supplied or approved body-worn
    a
    ccessories and are not using the radio held in the normal use position,
    e
    nsure the radio and its antenna are at least 1 inch (2.5 cm) from your
    b
    ody when transmitting.
    D
    ata Operation
    I
    f applicable, when using any data feature of the radio with or without an
    a
    ccessory cable, position the radio and its antenna at least one inch
    (2.5 cm) from the body.
    Approved Audio Accessories
    • 53724: Remote Speaker with Push-to-Talk Microphone
    • 53725: Headset with Swivel Boom Microphone
    53727: Earbud with Push-to-Talk Microphone
    53728: Flexible Ear Receiver
    56320: Earpiece with Boom Microphone
    E
    lectromagnetic Interference/Compatibility
    N
    ote: Nearly every electronic device is susceptible to electromagnetic
    interference (EMI) if inadequately shielded, designed or otherwise
    configured for electromagnetic compatibility. This device complies with
    Part 15 of the FCC Rules. Operation is subject to the following two
    c
    onditions:
    1
    . This device may not cause harmful interference; and
    2. This device must accept any interference received, including
    i
    nterference that may cause undesired operation.
    IC Canada
    T
    he term "IC:" before the equipment certification number only signifies
    t
    hat the Industry Canada technical specifications were met.
    F
    acilities
    T
    o avoid electromagnetic interference and/or compatibility conflicts, turn
    o
    ff your radio in any facility where posted notices instruct you to do so.
    Hospitals or health care facilities may be using equipment that is
    sensitive to external RF energy.
    A
    ircraft
    W
    hen instructed to do so, turn off your radio when onboard an aircraft.
    A
    ny use of a radio must be in accordance with applicable regulations
    per airline crew instructions.
    M
    edical Devices – Pacemakers
    T
    he Advanced Medical Technology Association recommends that a
    minimum separation of 6 inches (15 cm) be maintained between a
    handheld wireless radio and a pacemaker. These recommendations are
    consistent with the independent research by and recommendations of
    the U.S. Food and Drug Administration.
    People with pacemakers should:
    ALWAYS keep the radio more than 6 inches (15 cm) from their
    pacemaker when the radio is turned ON.
    Not carry the radio in the breast pocket.
    Use the ear opposite the pacemaker to minimize the potential for
    interference.
    Turn the radio OFF immediately if there is any reason to suspect that
    interference is taking place.
    Medical Devices – Hearing Aids
    Some digital wireless radios may interfere with some hearing aids. In the
    event of such interference, you may want to consult your hearing aid
    manufacturer to discuss alternatives.
    Medical Devices – Other
    If you use any other personal medical device, consult the manufacturer
    of your device to determine if it is adequately shielded from RF energy.
    Your physician may be able to assist you in obtaining this information.
    Safety and General Use While Driving
    Check the laws and regulations regarding the use of radios in the area
    where you drive, and always obey them. If you do use your radio while
    driving, please:
    Give full attention to driving and to the road.
    Use hands-free operation, if available.
    Pull off the road and park before making or answering a call if driving
    conditions so require.
    The use of a two-way radio while engaged in activities requiring
    concentration may cause distraction or otherwise impair your ability to
    safely participate in such activities. Always use technology safely.
    Do not place a portable radio in the area over an air bag or in the air bag
    deployment area. Air bags inflate with great force. If a portable radio is
    placed in the air bag deployment area and the air bag inflates, the radio
    may be propelled with great force and cause serious injury to occupants
    of the vehicle.
    Potentially Explosive Atmospheres
    Turn off your radio prior to entering any area with a potentially explosive
    atmosphere. Only radio types that are especially qualified should be
    used in such areas as “Intrinsically Safe.” Do not remove, install or
    charge batteries in such areas. Sparks in a potentially explosive
    atmosphere can cause an explosion or fire resulting in bodily injury or
    even death.
    F
    or More Information
    F
    or further information, you may call Motorola Solutions, Inc. at 1-800-638-
    5
    119 (U.S. and Canada), e-mail us at giantintl@callcenter.com or visit us
    o
    n the Internet at motorolasolutions.com/talkabout.
    N
    ote: The areas with potentially explosive atmospheres referred to above
    i
    nclude fueling areas such as below decks on boats, fuel or chemical
    t
    ransfer or storage facilities, areas where the air contains chemicals or
    particles (such as grain, dust or metal powders) and any other area
    where you would normally be advised to turn off your vehicle engine.
    A
    reas with potentially explosive atmospheres are often—but not
    a
    lways—posted.
    B
    lasting Caps and Areas
    T
    o avoid possible interference with blasting operations, turn off your
    r
    adio when you are near electrical blasting caps, in a blasting area, or in
    a
    reas posted “Turn off two-way radios.” Obey all signs and instructions.
    O
    perational Cautions
    A
    ntennas
    D
    o not use any portable radio that has a damaged antenna. If a
    damaged antenna comes into contact with your skin, a minor burn can
    result.
    B
    atteries
    All batteries can cause property damage and/or bodily injury such as burns
    if a conductive material—like jewelry, keys or beaded chains— touch
    exposed terminals. The conductive material may complete an electrical
    c
    ircuit (short circuit) and become quite hot. Exercise care in handling any
    c
    harged battery, particularly when placing it inside a pocket, purse or other
    c
    ontainer with metal objects.
    E
    xercise care when removing NiMH or AA batteries. Do not use sharp or
    c
    onductive tools to remove either of these batteries.
    Battery Charger Safety Instructions:
    Save these Instructions
    1. Do not expose the charger to rain or snow.
    2
    . Do not operate or disassemble the charger if it has received a sharp
    blow, or has been dropped or damaged in any way.
    3
    . Never alter the AC cord or plug provided with the unit. If the plug will
    not fit the outlet, have the proper outlet installed by a qualified
    electrician. An improper condition can result in a risk of electric
    shock.
    4. To reduce the risk of damage to the cord or plug, pull the plug rather
    than the cord when disconnecting the charger from the AC
    r
    eceptacle.
    5
    . To reduce the risk of electric shock, unplug the charger from the
    outlet before attempting any maintenance or cleaning.
    6
    . Use of an attachment not recommended or sold by Motorola may
    r
    esult in a risk of fire, electric shock or personal injury.
    7
    . Make sure the cord is located so it will not be stepped on, tripped
    over or subjected to damage or stress.
    8. An extension cord should not be used unless absolutely necessary.
    Use of an improper extension cord could result in a risk of a fire
    and/or electric shock. If an extension cord must be used, make sure
    that:
    The pins on the plug of the extension cord are the same number,
    size and shape as those on the plug of the charger.
    The extension cord is properly wired and in good condition.
    The extension cord size is 18 AWG for lengths up to 100 feet, and
    16 AWG for lengths up to 150 feet.
    9. The supply cord of the AC adaptor cannot be replaced. If the cord is
    damaged, call customer service at 1-800-638-5119 (U.S. and Canada)
    or e-mail us at giantintl@callcenter.com.
    Licensing Information
    Your Motorola radio operates on FRS & GMRS frequencies in Canada &
    in the USA. For Canadian citizens, use of these frequencies is subject to
    the rules & regulations of Industry Canada (IC). IC requires no license
    when operated in Canada. For USA citizens, use is subject to the rules
    and regulations of the Federal Communications Commission (FCC) . The
    FCC requires that all operators using GMRS frequencies obtain a radio
    license before operating their equipment. To obtain the FCC forms, please
    visit the FCC’s Web site at wireless.fcc.gov/uls/index.htm?job=home to
    source form 605 and 159, which includes all the instructions you will
    need. If you wish to have the document faxed or mailed, or if you have
    questions, please use the following contact information:
    Changes or modifications not expressly approved by Motorola may void
    the user’s authority granted by the IC/FCC to operate this radio and
    should not be made. To comply with IC/FCC requirements, transmitter
    adjustments should be made only by or under the supervision of a
    person certified as technically qualified to perform transmitter
    maintenance and repairs in the private land, mobile and fixed services
    as certified by an organization representative of the user of those
    services. Replacement of any transmitter component (crystal,
    semiconductor, etc.) not authorized by the IC/FCC equipment
    authorization for this radio could violate IC/FCC rules.
    Note: Use of this radio outside the country where it was intended to be
    distributed is subject to government regulations and may be prohibited.
    ®
    R
    adio Battery Meter
    T
    he radio battery icon shows the battery charge level, from full to
    e
    mpty . When the radio has one segment left, the
    radio chirps periodically or after releasing (Low Battery Alert).
    R
    emoving the NiMH Battery Pack
    1
    . Turn the radio off.
    2
    . With the back of the radio facing you, loosen the retaining screw on
    t
    he battery door and open the cover.
    3
    . Remove the NiMH battery pack by pulling the ribbon attached to
    t
    he radio.
    4
    . Close the battery cover and tighten the retaining screw on the
    b
    attery door.
    Removing the Three AA Alkaline Batteries (Optional Accessory)
    1
    . Turn the radio off.
    2. With the back of the radio facing you, loosen the retaining screw on
    t
    he battery door and open the cover.
    3. Gently remove each alkaline battery by easing each battery out
    i
    ndividually.
    4. Close the battery cover and tighten the retaining screw on the
    battery door.
    Notes
    Exercise care when removing NiMH or AA batteries. Do not use
    sharp or conductive tools to remove either of these batteries.
    Remove the batteries before storing your radio for extended periods
    of time. Batteries corrode over time and may cause permanent
    d
    amage to your radio.
    Using the mini-USB Charging Adaptor
    T
    he mini-USB charging adaptor allows you to conveniently charge your
    N
    iMH battery pack. This is an alternative to charging your NiMH battery
    p
    ack in the Battery Charger desk stand using the AC wall adaptor and
    especially useful when used while traveling.
    Available mini-USB charging options:
    1. Vehicle charger
    2
    . Mini-USB computer cable
    I
    f using a computer, the computer must be turned on.
    This and other accessories (sold separately) are available for your radio.
    For more information, visit our Web site at
    motorolasolutions.com/talkabout or shop.giantintl.com.
    1. Plug your mini-USB cable or charger into a power source as is
    a
    ppropriate for your accessory.
    2
    . Plug the cable into the mini-USB port on the bottom of your radio.
    3. After the initial charge, an empty battery will be fully charged in 7 hrs.
    for the MT350 series radio (KEBT-650 mAh NiMH battery pack) or 14
    hrs. for the MT352 series radio (KEBT-1300 mAh NiMH battery pack).
    4. The battery icon will scroll as the battery is being charged. The
    scrolling icon will stop when the battery is fully charged.
    Notes
    When moving between hot and cold temperatures, do not charge the
    NiMH battery pack until the battery temperature acclimates (usually
    about 20 minutes).
    For optimal battery life, remove the radio from the charger within 16
    hours. Do not store the radio while connected to the charger.
    If the radio is kept on while charging, the charging time will be
    extended.
    Even though the charger is connected, you may not be able to
    transmit a message if the battery is completely empty . Allow
    time for the battery to charge to 1 bar before attempting to
    transmit a message.
    Attaching and Removing the Belt Clip
    1. Attach belt clip to pocket or belt strap.
    2. Align the belt clip post with the hole in the back of the radio.
    3. Gently push until the clip clicks in place.
    To Remove
    1. Push down on the release tab at the top of the belt clip to release
    the catch.
    2. Pull the belt clip away from the back of the radio.
    Using the Desktop Battery Charger (Optional Accessory)
    The battery charger provides drop-in charging convenience for NiMH
    batteries and can be placed on any flat surface, such as a desk or
    workbench. Charge the NiMH battery overnight (at least 16 hours) before
    using it for the first time.
    MT350R Radio
    After the initial charge, an empty battery (KEBT-650 mAh NiMH) is fully
    charged within 7 hrs.
    MT352R Radio
    After the initial charge, an empty battery (KEBT-1300 mAh NiMH) is fully
    charged within 14 hrs.
    1. Follow the steps above to install a NiMH Battery Pack.
    2. Plug the AC power supply cord into the jack on the desk stand.
    3. Plug the AC power supply into a standard wall outlet.
    4. With a radio facing forward, slide it into one of the charging pockets.
    5. When charging in the battery charger, the red light on the charger
    base will glow continuously.
    T
    urning your Radio On and Off
    T
    urn clockwise to turn the radio on and counterclockwise to turn the
    radio off.
    1. In the ON position, the radio chirps and briefly shows all feature
    icons available on the radio.
    2
    . The display screen then shows the current channel, code and all
    features that are enabled.
    S
    etting the Volume
    P
    ress and hold for three seconds, then rotate until you reach a
    comfortable listening level.
    1. Rotate clockwise to increase the volume.
    2
    . Rotate counterclockwise to decrease the volume.
    Do not hold the radio close to your ear. If the volume is set to an
    u
    ncomfortable level, it could hurt your ear.
    Talking and Listening
    To communicate, all radios in your group must be set to the same
    c
    hannel and Interference Eliminator Code.
    1
    . To talk, press and hold .
    2
    . When you are finished talking, release .
    F
    or maximum clarity, hold the radio two to three inches away from your
    m
    outh and speak directly into the microphone. Do not cover the
    m
    icrophone while talking.
    Talk Range
    Your radio is designed to maximize performance and improve
    transmission range. Do not use the radios closer than five feet apart.
    Power Boost
    To boost your radio’s power up to high power, press the top portion of the
    b
    utton when talking. If you know your party is close by, you can
    c
    onserve your battery’s energy by pushing the lower part of the
    b
    utton to use less power.
    Note:
    I
    f you are on an FRS only channel (see Channels and Frequencies
    table) the radio will only use low power when either portion of the
    is pressed.
    M
    onitor Button
    Pressing and holding for three seconds allows you to listen to the
    volume level of the radio when you are not receiving. This allows you to
    adjust the volume, if necessary. You can also press to check for
    activity on the current channel before you talk.
    P
    ush to Talk Timeout Timer
    To prevent accidental transmissions and save battery life, the radio emits
    a continuous warning tone and stops transmitting if you press for 60
    continuous seconds.
    Menu Options
    Selecting the Channel
    Your radio has 22 channels. The channel is the frequency the radio uses to
    transmit. Channels 8-14 are FRS 0.5 watt only and all other channels are
    GMRS. (See the "Channels and Frequencies" table on overleaf for details.)
    1. With the radio on, press . When the radio is on a 0.5
    watt channel, displays. When the radio is on a 1.5 watts
    channel, displays. The current channel flashes.
    2. Press or and select an unused or quiet channel.
    3. Press to save the channel setting or to continue set up.
    Selecting the Interference Eliminator Code
    Interference Eliminator Codes help minimize interference by blocking
    transmissions from unknown sources. Your radio has 121 Interference
    Eliminator Codes. Codes 1 – 38 are the standard analog codes that
    appear on other FRS/GMRS radios. Codes 39 – 121 are additional digital
    codes added for superior interference protection. 0 is the off position, no
    analog or digital codes are enabled.
    To set the code for a channel:
    1. Press until the code starts to flash.
    2. Press or to select the code.
    3. Press to save the code setting or to continue set up.
    You can set a different code for each channel using this procedure. An
    extended press of or allows you to scroll through the Interference
    Code rapidly so you can quickly reach the code you want.
    Note: You must set the Interference Eliminator Code to 0 on a radio that
    uses Interference Eliminator Codes to communicate with radios that do
    not have Interference Eliminator Codes. Select 0 for “no tone, no code”
    and OFF will flash on your radio’s display.
    Setting and Transmitting Call Tones
    Your radio can transmit different call tones to other radios in your group
    so you can alert them that you want to talk. Your radio has 20 call tones
    from which to choose.
    To set a call tone:
    1. Press three times until the current call tone setting flashes and
    appears.
    2. Press or to change and hear the call tone.
    Display Screen Guide
    Continued on back
    MT Series
    Control Buttons
    MON
    MENU
    E
    mergency Alert
    Flash Light LED
    Menu/ Keypad Lock
    Scan/Monitor
    Speaker
    A
    ccessory Port
    LED Indicator
    Call Tone
    Microphone
    F
    lash Light
    B
    utton
    V
    olume
    Push to Talk
    (High)
    Push to Talk
    (Low)
    Scroll/Weather
    Mini-USB
    Charging Port
    Numbers for Codes
    Numbers for Channel,
    C
    all Tone
    —Battery Meter
    —Channel Power
    Indicator
    (see menu Options)
    Keypad Lock
    —Talk Confirmation
    Tone (Roger Beep)
    —Noise Filtering
    —On/Off for each
    feature
    —Scan
    —Call Tone,
    Keypad Tone
    —Weather Alert
    Hands-Free Use
    Without
    Accessories
    —Hands-Free Use
    With Accessories
    —Dual Scan
    —Vibrate
    Numbers for Codes
    Numbers for Channel,
    C
    all Tone
    Battery Meter
    —Channel Power
    Indicator
    (see menu Options)
    —Keypad Lock
    —Talk Confirmation
    Tone (Roger Beep)
    —Noise Filtering
    —On/Off for each
    feature
    —Scan
    Call Tone,
    Keypad Tone
    —Weather Alert
    —Hands-Free Use
    Without
    Accessories
    —Hands-Free Use
    With Accessories
    Dual Scan
    —Vibrate
    Emergency Alert
    Flash Light LED
    Menu/ Keypad Lock
    Scan/Monitor
    Speaker
    Accessory Port
    LED Indicator
    Call Tone
    Microphone
    Flash Light
    Button
    Volume
    Push to Talk
    (High)
    Push to Talk
    (Low)
    Scroll/Weather
    Mini-USB
    Charging Port
    MON
    M
    ENU
    MT350
    Line Drawing best fitting for UG
    Getting Started
    Weatherproof
    This radio is weatherproof to IP-54 standards. It is dust/splashproof from
    any direction. The radio is resistant to water and rain splashes only
    when the battery cover and headset accessory mini-USB ports are
    sealed. Open the battery compartment door or headset port cover only
    when the radio is dry. Use of a headset accessory should be in dry
    environments only.
    The charging base and AC adaptor are not waterproof. Do not expose the
    charger to rain or snow. Charge the radios only in a dry location. Do not
    place wet radios into the charging base. The battery door must be tightly
    closed with the screw to maintain the weatherproof seal of the radio.
    Installing the Batteries
    Each radio can use either 1 NiMH rechargeable battery pack or 3 AA
    alkaline batteries and beeps when the batteries are low.
    Installing NiMH Rechargeable Battery Pack
    1. Turn the radio off.
    2. With the back of the radio facing you, loosen the retaining screw on
    the battery door and open the cover.
    3. Remove the NiMH battery pack from the clear plastic bag (do not
    disassemble or unwrap the battery pack).
    4. Insert the NiMH battery pack with the diagram facing you. (The
    ribbon should be underneath the battery pack and should wrap
    around the right side of the pack for easy removal.)
    5. Close the battery cover and tighten the retaining screw on the
    battery door.
    Installing the Three AA Alkaline Batteries (Optional Accessory)
    1. Turn the radio off.
    2. With the back of the radio facing you, loosen the retaining screw on
    the battery door and open the cover.
    3. Insert the three AA alkaline batteries with + and - polarity as shown
    inside. (The ribbon should be underneath the AA alkaline batteries
    and should wrap around the right side of the batteries.)
    4. Close the battery cover and tighten the retaining screw on the
    battery door.
    For a fax:
    Contact the
    Fax-0n-Demand
    system
    For mail service:
    Call the FCC
    Forms Hotline
    If you have
    questions about
    the FCC License:
    Call the FCC
    1-202-418-0177 1-800-418-FORM
    (3676)
    1-888-CALL-FCC
    (225-5322)
    Two-Way Radio
    User Guide
    M
    ON
    M
    ENU
    E
    mergency Alert
    Flash Light LED
    Menu/ Keypad Lock
    Scan/Monitor
    Speaker
    Accessory Port
    LED Indicator
    Call Tone
    Microphone
    Flash Light
    Button
    Volume
    Push to Talk
    (High)
    Push to Talk
    (Low)
    Scroll/Weather
    Mini-USB
    Charging Port
    Numbers for Codes
    Numbers for Channel,
    C
    all Tone
    —Battery Meter
    —Channel Power
    Indicator
    (see menu Options)
    —Keypad Lock
    —Talk Confirmation
    Tone (Roger Beep)
    —Noise Filtering
    —On/Off for each
    feature
    —Scan
    —Call Tone,
    Keypad Tone
    —Weather Alert
    —Hands-Free Use
    Without
    Accessories
    —Hands-Free Use
    With Accessories
    —Dual Scan
    Vibrate
    N
    umbers for Codes
    N
    umbers for Channel,
    C
    all Tone
    Battery Meter
    —Channel Power
    Indicator
    (see menu Options)
    Keypad Lock
    —Talk Confirmation
    Tone (Roger Beep)
    Noise Filtering
    On/Off for each
    feature
    Scan
    —Call Tone,
    Keypad Tone
    Weather Alert
    —Hands-Free Use
    Without
    Accessories
    Hands-Free Use
    With Accessories
    Dual Scan
    —Vibrate
    Emergency Alert
    Flash Light LED
    M
    enu/ Keypad Lock
    Scan/Monitor
    Speaker
    A
    ccessory Port
    LED Indicator
    Call Tone
    Microphone
    Flash Light
    B
    utton
    Volume
    Push to Talk
    (High)
    Push to Talk
    (Low)
    S
    croll/Weather
    Mini-USB
    Charging Port
    MON
    MENU
    MT350
    Line Drawing best fitting for UG
Motorola MT352TPR

Trebate pomoć?

Broj pitanja: 0

Imate li pitanja u vezi s proizvodom MT352TPR trgovačke marke Motorola ili vam treba pomoć? Ovdje postavite svoje pitanje. Navedite jasan i sveobuhvatan opis problema i vašeg pitanja. Što više pojedinosti navedete za svoje pitanje i pitanje, lakše je drugim vlasnicima proizvoda MT352TPR trgovačke marke Motorola pravilno odgovoriti na vaše pitanje.

Ovdje besplatno pogledajte priručnik za proizvod MT352TPR trgovačke marke Motorola. Ovaj je priručnik pod kategorijom , a ocijenio ga je sljedeći broj osoba: 1 prosječnom ocjenom od 7.4. Ovaj je priručnik dostupan na sljedećim jezicima: Engleski. Imate li pitanja u vezi s proizvodom MT352TPR trgovačke marke Motorola ili vam treba pomoć? Ovdje postavite svoje pitanje

Značajke proizvoda MT352TPR trgovačke marke Motorola

Brend Motorola
Model MT352TPR
Proizvod Voki-toki
Jezik Engleski
Vrsta datoteke PDF

Povezani priručnici za proizvode

Voki-toki Motorola

prirucnici.hr

Tražite priručnik? prirucnici.hr osigurava da u trenu pronađete priručnik koji tražite. Naša baza podataka sadrži više od milijun PDF priručnika za više od 10,000 robnih marki. Svaki dan dodajemo najnovije priručnike pa ćete uvijek pronaći proizvod koji tražite. Vrlo je jednostavno: samo u tražilicu upišite naziv robne marke i vrstu proizvoda i odmah ćete vidjeti priručnik po svom izboru na Internetu, besplatno.

prirucnici.hr

© Autorska prava 2020 prirucnici.hr. Sva prava pridržana.