Motorola MH230TPR

Motorola MH230TPR priručnik

(1)
  • MH Series
    KEM-PK14190-75
    Safety and General Information
    Important Information on Safe and Efficient Operation
    Read This Information Before Using Your Radio.
    The information provided in this document supersedes the general
    safety information in user guides published prior to December 1, 2002.
    Transmit and Receive Procedure
    Your two-way radio contains a transmitter and a receiver. To control
    your exposure and ensure compliance with the general population/
    uncontrolled environment exposure limits, always adhere to the
    following procedure:
    Transmit no more than 50% of the time.
    To receive calls, release the PTT button.
    To transmit (talk), press the Push to Talk (PTT) button.
    Transmitting 50% of the time, or less, is important because the radio
    generates measurable RF energy exposure only when transmitting
    (in terms of measuring standards compliance).
    Exposure to Radio Frequency Energy
    Your Motorola two-way radio complies with the following RF energy
    exposure standards and guidelines:
    United States Federal Communications Commission, Code of
    Federal Regulations; 47CFR part 2 sub-part J.
    American National Standards Institute (ANSI)/Institute of
    Electrical and Electronic Engineers (IEEE) C95. 1-1992.
    Institute of Electrical and Electronics Engineers (IEEE) C95.
    1-1999 Edition.
    International Commission on Non-Ionizing Radiation Protection
    (ICNIRP) 1998.
    Ministry of Health (Canada) Safety Code 6. Limits of Human
    Exposure to Radiofrequency Electromagnetic Fields in the
    Frequency Range from 3 KHz to 300 GHz, 1999.
    Australian Communications Authority Radiocommunications
    (Electromagnetic Radiation—Human Exposure) Standard, 2003.
    ANATEL ANNEX to Resolution No. 303 of July 2, 2002 “Regulation of
    limitation of exposure to electrical, magnetic and electromagnetic
    fields in the radio frequency range between 9 KHz and 300GHz”.
    To ensure optimal radio performance and make sure human
    exposure to radio frequency electromagnetic energy is within the
    guidelines set forth in the above standards, always adhere to the
    following procedures.
    Portable Radio Operation and EME Exposure
    Antenna Care
    Use only the supplied or an approved replacement antenna.
    Unauthorized antennas, modifications, or attachments could
    damage the radio and may violate FCC regulations.
    Do NOT hold the antenna when the radio is “IN USE.” Holding the
    antenna affects its effective range.
    Body-Worn Operation
    To maintain compliances with FCC/Health Canada RF exposure
    guidelines if you wear a radio on your body when transmitting
    always place the radio in a Motorola-supplied or approved clip
    holder, holster, case or body harness for this product. Use of non-
    Motorola-approved accessories may exceed FCC/Health Canada RF
    exposure guidelines.
    If you do not use one of the Motorola-supplied or approved body-
    worn accessories and are not using the radio held in the normal
    use position, ensure the radio and its antenna are at least 1 inch
    (2.5 cm) from your body when transmitting.
    Data Operation
    If applicable, when using any data feature of the radio with or
    without an accessory cable, position the radio and its antenna at
    least one inch (2.5 cm) from the body.
    Approved Accessories
    For a list of approved Motorola accessories, visit our Web site at
    www.motorola.com.
    Electromagnetic Interference/Compatibility
    Note: Nearly every electronic device is susceptible to
    electromagnetic interference (EMI) if inadequately shielded,
    designed or otherwise configured for electromagnetic compatibility.
    This device complies with Part 15 of the FCC Rules.
    Operation is subject to the following two conditions:
    1. This device may not cause harmful interference; and
    2. This device must accept any interference received, including
    interference that may cause undesired operation.
    IC Canada
    The term "IC:" before the equipment certification number only
    signifies that the Industry Canada technical specifications were met.
    Facilities
    To avoid electromagnetic interference and/or compatibility conflicts,
    turn off your radio in any facility where posted notices instruct you
    to do so. Hospitals or health care facilities may be using equipment
    that is sensitive to external RF energy.
    Aircraft
    When instructed to do so, turn off your radio when onboard an
    aircraft. Any use of a radio must be in accordance with applicable
    regulations per airline crew instructions.
    Medical Devices Pacemakers
    The Advanced Medical Technology Association recommends that
    a minimum separation of 6 inches (15 cm) be maintained between a
    handheld wireless radio and a pacemaker. These recommendations
    are consistent with the independent research by and
    recommendations of the U.S. Food and Drug Administration.
    People with pacemakers should:
    ALWAYS keep the radio more than 6 inches (15 cm) from their
    pacemaker when the radio is turned ON.
    Not carry the radio in the breast pocket.
    Use the ear opposite the pacemaker to minimize the potential
    for interference.
    Turn the radio OFF immediately if there is any reason to suspect
    that interference is taking place.
    Medical Devices Hearing Aids
    Some digital wireless radios may interfere with some hearing aids.
    In the event of such interference, you may want to consult your
    hearing aid manufacturer to discuss alternatives.
    Medical Devices Other
    If you use any other personal medical device, consult the
    manufacturer of your device to determine if it is adequately
    shielded from RF energy. Your physician may be able to assist you
    in obtaining this information.
    Safety and General Use While Driving
    Check the laws and regulations regarding the use of radios in the
    area where you drive, and always obey them. If you do use your
    radio while driving, please:
    Give full attention to driving and to the road.
    Use hands-free operation, if available.
    Pull off the road and park before making or answering a call if
    driving conditions so require.
    The use of a two-way radio while engaged in activities requiring
    concentration may cause distraction or otherwise impair your
    ability to safely participate in such activities. Always use technology
    safely.
    Do not place a portable radio in the area over an air bag or in the
    air bag deployment area. Air bags inflate with great force. If a
    portable radio is placed in the air bag deployment area and the air
    bag inflates, the radio may be propelled with great force and cause
    serious injury to occupants of the vehicle.
    Potentially Explosive Atmospheres
    Turn off your radio prior to entering any area with a potentially
    explosive atmosphere. Only radio types that are especially qualified
    should be used in such areas as “Intrinsically Safe.” Do not remove,
    install or charge batteries in such areas. Sparks in a potentially
    explosive atmosphere can cause an explosion or fire resulting in
    bodily injury or even death.
    For More Information
    For further information, you may call Motorola at 1-800-638-5119
    (U.S. and Canada), or e-mail us at giantintl@callcenter.com or visit
    us on the Internet at www.motorola.com.
    Note: The areas with potentially explosive atmospheres referred to
    above include fueling areas such as below decks on boats, fuel or
    chemical transfer or storage facilities, areas where the air contains
    chemicals or particles (such as grain, dust or metal powders) and
    any other area where you would normally be advised to turn off your
    vehicle engine. Areas with potentially explosive atmospheres are
    often—but not always—posted.
    Blasting Caps and Areas
    To avoid possible interference with blasting operations, turn off your
    radio when you are near electrical blasting caps, in a blasting area,
    or in areas posted “Turn off two-way radios.” Obey all signs and
    instructions.
    Operational Cautions
    Antennas
    Do not use any portable radio that has a damaged antenna. If a
    damaged antenna comes into contact with your skin, a minor burn
    can result.
    Batteries
    All batteries can cause property damage and/or bodily injury such as
    burns if a conductive material—like jewelry, keys or beaded chains—
    touch exposed terminals. The conductive material may complete an
    electrical circuit (short circuit) and become quite hot. Exercise care in
    handling any charged battery, particularly when placing it inside a
    pocket, purse or other container with metal objects.
    Exercise care when removing NiMH or AAA batteries. Do not use
    sharp or conductive tools to remove either of these batteries.
    Battery Charger Safety Instructions:
    Save these Instructions
    1. Do not expose the charger to rain or snow.
    2. Do not operate or disassemble the charger if it has received a
    sharp blow, or has been dropped or damaged in any way.
    3. Never alter the AC cord or plug provided with the unit. If the
    plug will not fit the outlet, have the proper outlet installed by a
    qualified electrician. An improper condition can result in a risk
    of electric shock.
    4. To reduce the risk of damage to the cord or plug, pull the plug
    rather than the cord when disconnecting the charger from the
    AC receptacle.
    5. To reduce the risk of electric shock, unplug the charger from the
    outlet before attempting any maintenance or cleaning.
    6. Use of an attachment not recommended or sold by Motorola
    may result in a risk of fire, electric shock or personal injury.
    7. Make sure the cord is located so it will not be stepped on,
    tripped over or subjected to damage or stress.
    8. An extension cord should not be used unless absolutely
    necessary. Use of an improper extension cord could result in a
    risk of a fire and/or electric shock. If an extension cord must be
    used, make sure that:
    The pins on the plug of the extension cord are the same
    number, size and shape as those on the plug of the charger.
    The extension cord is properly wired and in good electrical
    condition.
    The extension cord size is 18 AWG for lengths up to 100 feet,
    and 16 AWG for lengths up to 150 feet.
    9. The supply cord of the AC adaptor cannot be replaced. If the
    cord is damaged, call customer service at 1-800-638-5119 (U.S.
    and Canada) or e-mail us at giantintl@callcenter.com.
    FCC Licensing Information
    Your Motorola radio operates on General Mobile Radio Service
    (GMRS) frequencies and is subject to the Rules and Regulations of
    the Federal Communications Commission (FCC). The FCC requires
    that all operators using GMRS frequencies obtain a radio license
    before operating their equipment. To obtain the FCC forms, please
    visit the FCC’s Web site at wireless.fcc.gov/uls/index.htm?job=home
    to source form 605 and 159, which includes all the instructions you
    will need.
    If you wish to have the document faxed or mailed, or if you have
    questions, please use the following contact information:
    Changes or modifications not expressly approved by Motorola may
    void the user’s authority granted by the FCC to operate this radio
    and should not be made. To comply with FCC requirements,
    transmitter adjustments should be made only by or under the
    supervision of a person certified as technically qualified to perform
    transmitter maintenance and repairs in the private land mobile and
    fixed services as certified by an organization representative of the
    user of those services. Replacement of any transmitter component
    (crystal, semiconductor, etc.) not authorized by the FCC equipment
    authorization for this radio could violate FCC rules.
    ®
    3. Gently remove each battery by easing each battery out individually.
    4. Reposition the battery cover and press down to secure.
    Notes
    Exercise care when removing NiMH or AAA batteries. Do not
    use sharp or conductive tools to remove either of these batteries.
    Remove the batteries before storing your radio for extended
    periods of time. Batteries corrode over time and may cause
    permanent damage to your radio.
    Using the Battery Charger (Optional Accessory)
    The battery charger provides drop-in charging convenience for
    NiMH batteries and can be placed on any flat surface, such as a
    desk or workbench. Charge the NiMH battery overnight (at least
    16 hours) before using it for the first time. After the initial charge,
    an empty battery is fully charged within 14 hours.
    1. Follow the steps above to install a NiMH Battery Pack.
    2. Plug the AC power supply cord into the jack on the desk stand.
    3. Plug the AC power supply into a standard wall outlet.
    4. With a radio facing forward, slide it into one of the charging
    pockets.
    5. When charging in the battery charger, the red light on the
    charger base will glow continuously.
    Using the mini-USB Charging Connector
    The mini-USB charging connector is a handy port that allows you to
    conveniently charge your NiMH battery pack. This is an alternative
    to charging your NiMH battery pack in the Battery Charger desk
    stand using the AC wall adaptor and especially useful when used
    while traveling.
    Available mini-USB charging options: (Optional Accessories)
    1. Wall travel charger
    2. Vehicle charger
    3. Mini-USB computer cable
    If using a computer, the computer must be turned on.
    This and other accessories (sold separately) are available for
    your radio. For more information, visit our Web site at
    www.motorola.com or shop.giantintl.com.
    1. Plug your mini-USB cable or charger into a power source as is
    appropriate for your accessory.
    2. Plug the cable into the mini-USB port on the bottom of your radio.
    3. An empty battery will be fully charged in 14 hours.
    4. The LED indicator light on the radio will glow to indicate that the
    battery is charging.
    Notes
    The light will remain red after the NiMH battery pack is fully
    charged.
    When moving between hot and cold temperatures, do not
    charge the NiMH battery pack until the battery temperature
    acclimates (usually about 20 minutes).
    For optimal battery life, remove the radio from the charger within
    16 hours. Do not store the radio while connected to the charger.
    If the radio is kept on while charging, the charging time will be
    extended.
    Even though the charger is connected, you may not be able to
    transmit a message if the battery is completely empty .
    Allow time for the battery to charge to 1 bar before
    attempting to transmit a message.
    Attaching and Removing the Belt Clip
    1. Attach belt clip to pocket or belt strap.
    2. Align the belt clip post with the hole in the back of the radio.
    3. Gently push until the clip clicks in place.
    To Remove
    1. Push down on the release tab at the top of the belt clip to
    release the catch.
    2. Pull the belt clip away from the back of the radio.
    Turning your Radio On and Off
    Turn clockwise to turn the radio on and counterclockwise to
    turn the radio off.
    1. In the ON position, the radio chirps and briefly shows all feature
    icons available on the radio.
    2. The display screen then shows the current channel, code and
    all features that are enabled.
    Setting the Volume
    Press and hold for three seconds while rotating until you
    reach a comfortable listening level.
    1. Rotate clockwise to increase the volume.
    2. Rotate counterclockwise to decrease the volume.
    Do not hold the radio close to your ear. If the volume is set to an
    uncomfortable level, it could hurt your ear.
    Talking and Listening
    To communicate, all radios in your group must be set to the same
    channel and Interference Eliminator Code.
    1. To talk, press and hold .
    2. When you are finished talking, release .
    For maximum clarity, hold the radio two to three inches away from
    your mouth and speak directly into the microphone. Do not cover
    the microphone while talking.
    Talk Range
    Your radio is designed to maximize performance and improve
    transmission range. Do not use the radios closer than five feet apart.
    Monitor Button
    Pressing and holding for three seconds allows you to listen to
    the volume level of the radio when you are not receiving. This allows
    you to adjust the volume, if necessary. You can also press to
    check for activity on the current channel before you talk.
    Push to Talk Timeout Timer
    To prevent accidental transmissions and save battery life, the radio
    emits a continuous warning tone and stops transmitting if you
    press for 60 continuous seconds.
    Menu Options
    Selecting the Channel
    Your radio has 22 channels. The channel is the frequency the radio
    uses to transmit. Channels 8-14 are FRS 0.5 watt only and all other
    channels are GMRS. (See the “Channels and Frequencies” table on
    overleaf for details.)
    1. With the radio on, press . When the radio is on a 0.5 watt
    channel, displays. When the radio is on a 1 watt channel,
    displays. The current channel flashes.
    2. Press or and select an unused or quiet channel.
    3. Press to save the channel setting or to continue set up.
    Selecting the Interference Eliminator Code
    Interference Eliminator Codes help minimize interference by
    blocking transmissions from unknown sources. Your radio has 121
    Interference Eliminator Codes. Codes 1 38 are the standard analog
    codes that appear on other FRS/GMRS radios. Codes 39 121 are
    additional digital codes added for superior interference protection.
    0 is the off position, no analog or digital codes are enabled.
    To set the code for a channel:
    1. Press until the code starts to flash.
    2. Press or to select the code.
    3. Press to save the code setting or to continue set up.
    You can set a different code for each channel using this procedure.
    An extended press of or allows you to scroll through
    the Interference Code rapidly so you can quickly reach the code
    you want.
    Note: You must set the Interference Eliminator Code to 0 on a radio
    that uses Interference Eliminator Codes to communicate with radios
    that do not have Interference Eliminator Codes. Select 0 for “no
    tone, no code” and OFF will flash on your radio’s display.
    Setting and Transmitting Call Tones
    Your radio can transmit different call tones to other radios in your
    group so you can alert them that you want to talk. You have 10 call
    tones from which to choose.
    To set a call tone:
    1. With the radio on, press three times until the current
    call tone setting (0 - 10) flashes and appears.
    2. Press or to change and hear the call tone.
    3. Press to set the new call tone or to continue set up.
    To transmit your call tone to other radios set to the same channel
    and Interference Eliminator Code as your radio, press .
    Note: Setting the call to 0 disables the call tone feature.
    Hands-Free Use Without Accessories ( )
    You can use the iVOX feature to transmit hands-free without the need
    for any headset accessories. Once iVOX is turned on, the radio detects
    your voice and transmits when you speak into the internal microphone.
    1. Press until appears on the display. The current
    setting On/Off will flash.
    2. Press or to select On or Off.
    3. Press to set or to continue set up.
    Hands-Free Use With Accessories ( )
    You can transmit hands-free more reliably with the use of optional
    headset accessories. Once VOX is turned on, the radio detects your
    voice and transmits when you speak.
    Many accessories (sold separately) are available for your radio.
    For more information, visit our Web site at www.motorola.com or
    shop.giantintl.com.
    1. Turn the radio off and plug the VOX accessory into the
    accessory port.
    2. Turn the radio on. VOX shows on the display.
    3. Adjust the volume appropriately by rotating . Lower the
    volume before placing the accessory on your head or in your ear.
    4. To turn off, simply remove accessory.
    Display Screen Guide
    Continued on back
    MH Series
    Control Buttons
    Getting Started
    Installing the Batteries
    Each radio uses 1 NiMH rechargeable battery pack or 3 AAA
    alkaline batteries and beeps when the batteries are low.
    Installing NiMH Rechargeable Battery Pack (Optional Accessory)
    1. Turn the radio off.
    2. With the back of the radio facing you, lift the battery cover latch
    up and remove the cover.
    3. Remove the battery pack from the clear plastic bag. (Do not
    disassemble or unwrap the battery pack.)
    4. Insert the NiMH battery pack with the diagram facing you.
    5. Reposition the battery cover and press down to secure.
    Installing the Three AAA Alkaline Batteries
    1. Turn the radio off.
    2. With the back of the radio facing you, lift the battery cover latch
    up and remove the cover.
    3. Insert the three AAA alkaline batteries with + and - polarity as
    shown inside.
    4. Reposition the battery cover and press down to secure.
    Radio Battery Meter
    The radio battery icon shows the radio battery charge level, from
    full to empty . When the radio has one segment left, the
    radio chirps periodically or after releasing (Low Battery Alert).
    Removing the NiMH Battery Pack (Optional Accessory)
    1. Turn the radio off.
    2. With the back of the radio facing you, lift the battery latch up to
    release the battery cover and remove the cover.
    3. Remove the NiMH battery pack by pulling the ribbon attached to
    the battery.
    4. Reposition the battery cover and press down to secure.
    Removing the Three AAA Batteries
    1. Turn the radio off.
    2. With the back of the radio facing you, lift the battery latch up to
    release the battery cover and remove the cover.
    For a fax:
    Contact the
    Fax-0n-Demand
    system
    For mail service:
    Call the FCC
    Forms Hotline
    If you have
    questions about
    the FCC License:
    Call the FCC
    1-202-418-0177 1-800-418-FORM
    (3676)
    1-888-CALL-FCC
    (225-5322)
    Two-Way Radio
    User’s Guide
    Numbers
    for Channel,
    C
    all Tone
    Numbers
    f
    or Codes
    -
    Battery Meter
    -
    Channel Power
    Indicator (see
    M
    enu Options)
    -
    Lock
    -
    Talk Confirmation
    Tone (Roger Beep)
    -
    Noise Filtering
    -
    O
    n/Off for each
    feature
    -
    Scan
    -
    Call Tone,
    Keypad Tone
    -
    W
    eather Alert
    -
    Hands-Free Use
    Without
    Accessories
    -
    Hands-Free Use
    With Accessories
    Push to Talk
    Call Tone
    Speaker
    Menu/Lock
    Accessory Jack
    Scan/Monitor
    Scroll/Weather
    Microphone
    Volume
    Mini-USB
    Charging Port
Motorola MH230TPR

Trebate pomoć?

Broj pitanja: 0

Imate li pitanja u vezi s proizvodom MH230TPR trgovačke marke Motorola ili vam treba pomoć? Ovdje postavite svoje pitanje. Navedite jasan i sveobuhvatan opis problema i vašeg pitanja. Što više pojedinosti navedete za svoje pitanje i pitanje, lakše je drugim vlasnicima proizvoda MH230TPR trgovačke marke Motorola pravilno odgovoriti na vaše pitanje.

Ovdje besplatno pogledajte priručnik za proizvod trgovačke marke . Ovaj je priručnik pod kategorijom , a ocijenio ga je sljedeći broj osoba: prosječnom ocjenom od . Ovaj je priručnik dostupan na sljedećim jezicima: . Imate li pitanja u vezi s proizvodom trgovačke marke ili vam treba pomoć? Ovdje postavite svoje pitanje

Značajke proizvoda MH230TPR trgovačke marke Motorola

Brend Motorola
Model MH230TPR
Proizvod Voki-toki
Jezik Engleski
Vrsta datoteke PDF

Povezani priručnici za proizvode

Voki-toki Motorola