Metra CHTO-01

Metra CHTO-01 priručnik

  • CHRYSLER CAN BUS INTERFACE
    ©Copyright 2004-2010 Metra Electronics Corporation
    1-800-221-0932
    www.metraonline.com
    CHTO-01
    INSTALLATION INSTRUCTIONS
    * IMPORTANT WARNING
    THIS PRODUCT INCLUDES INSTRUCTIONS FOR INSTALLATION WHICH MUST
    BE CAREFULLY FOLLOWED. THE INSTRUCTIONS ARE WORDED IN SUCH A
    MANNER TO ASSUME THAT THE INSTALLER IS CAPABLE OF COMPLETING
    THESE TYPE OF ELECTRONIC INSTALLATIONS. IF YOU ARE UNCLEAR AS TO
    WHAT YOU ARE INSTRUCTED TO DO OR BELIEVE THAT YOU DO NOT UNDER-
    STAND THE INSTRUCTIONS SO AS TO PROPERLY AND SAFELY COMPLETE
    THE INSTALLATION YOU SHOULD CONSUL
    T A TECHNICIAN WHO DOES HAVE
    THIS KNOWLEDGE AND UNDERSTANDING. FAILURE TO FOLLOW THESE
    INSTRUCTIONS CAREFULLY AND TO INSTALL THE INTERFACE AS
    DESCRIBED COULD CAUSE HARM TO THE VEHICLE OR TO SAFETY
    SYSTEMS ON THE VEHICLE. INTERFERENCE WITH CERTAIN SAFETY
    SYSTEMS COULD CAUSE HARM TO PERSONS AS WELL. IF YOU HAVE ANY
    QUESTIONS IN THIS REGARD PLEASE CALL THE HELP LINE OR THE
    METRA AT 1-800-221-0932 FOR ASSISTANCE.
    CHTO-01 CHTO-01
    * READ IMPORTANT WARNING INSIDE
    BEFORE ATTEMPTING ANY INSTALLATION
    THE CHTO-01 IS DESIGNED TO BE USED WITH VEHI-
    CLES THAT HAVE A FACTORY AMPLIFIED SYSTEM.
    THE CHTO-01 WILL PROVIDE A 12VOLT SWITCHED
    WIRE FOR PROPER RADIO OPERATION. THE CHTO-01
    NOW PROVIDES MUTE, PARKING BRAKE, VSS OR
    SPEED SENSE, AND A REVERSE OUTPUT TO MAKE
    INSTALLING AN AFTERMARKET NAVIGATIONAL
    RADIO SIMPLER AND LESS TIME COMSUMING.
    Cutting Tool • Tape • Crimping Tool • Connectors
    TOOLS REQUIRED FOR INST
    ALLATION
    AUDIO LEVEL CONTROL
    When using the CHTO-01 with a radio that has a high audio pre-out voltage,
    usually greater than 2 volts, the audio signal may become distorted.
    To resolve this follow these steps:
    1. Make sure the ignition is turned to the “off” position.
    2. Disconnect both of the harnesses from the CHTO-01.
    3. Locate the potentiometer next to the 14 pin connector at the end of the CHTO-01.
    4. Taking a small flat headed screwdriver, turn the potentiometer counter-
    c
    lockwise to lower the input level going to the factory amplifier.
    5. After making the adjustment reconnect the wire harnesses.
    4
    REV. 05-10-10 INSTCHTO-01
    POTENTIOMETER
    AUDIO LEVEL
    ADJUSTMENT
    INTERF
    ACE COMPONENTS
    CHTO-01
    14 PIN HARNESS WITH RCA’S
    12 PIN HARNESS TO 22 PIN CHRYSLER HARNESS

Imate li pitanja o Metra CHTO-01?

Ovdje jednostavno postavite pitanje koje imate o Metra CHTO-01 drugim vlasnicima proizvoda. Navedite jasan i sveobuhvatan opis problema i svoje pitanje. Što bolje opišete svoj problem i pitanje, drugi vlasnici Metra CHTO-01 će Vam jednostavnije dati dobar odgovor.

Ovdje besplatno pročitajte Metra CHTO-01 priručnik. Pročitali ste priručnik, ali odgovara li on na Vaše pitanje? Postavite onda svoje pitanje na ovoj stranici drugim vlasnicima Metra CHTO-01.

Specifikacije proizvoda

Brend Metra
Model CHTO-01
Proizvod Pribor za automobil
EAN 86429154883, 88020937216
Jezik Engleski
Vrsta datoteke PDF
Tehničke pojedinosti
Kompatibilni proizvodi Chrysler

Kupite povezane proizvode:

    Povezani proizvodi

    Pribor za automobil Metra