Honeywell RTH230B priručnik

Honeywell RTH230B
9.2 · 2
PDF priručnik
 · 4 stranice/a
Engleski
priručnikHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

Ovdje besplatno pogledajte priručnik za proizvod RTH230B trgovačke marke Honeywell. Ovaj je priručnik pod kategorijom , a ocijenio ga je sljedeći broj osoba: 2 prosječnom ocjenom od 9.2. Ovaj je priručnik dostupan na sljedećim jezicima: Engleski. Imate li pitanja u vezi s proizvodom RTH230B trgovačke marke Honeywell ili vam treba pomoć? Ovdje postavite svoje pitanje

Trebate pomoć?

Imate li pitanja o Honeywell , a odgovor nije u priručniku?

  • Primajte ažuriranja o rješenjima
  • Dobijte odgovore na svoja pitanja

Pitanje i odgovor

Broj pitanja: 0

Honeywell RTH230B je programabilni termostat koji olakšava upravljanje grijanjem i hlađenjem u kući ili poslovnom prostoru. Ovaj termostat dolazi sa velikim LCD ekranom koji prikazuje trenutnu temperaturu i podešavanja korisnika. Idealno je rješenje za one koji žele uštedu energije, jer se može programirati u skladu sa svojim rasporedom dana, prilagođavajući temperaturu vašim životnim potrebama tokom dana. Može se podesiti na temperaturu zahtjevanu u večernjim ili jutarnjim satima, te će se sama gasiti kad više nije potrebno zagrijavanje ili hlađenje prostora. Ovaj termostat može se lako instalirati, a komunikacija s električnim sustavom vrši se pomoću žica. Iako se radi o jednostavnom uređaju, Honeywell RTH230B ima nekoliko dodatnih funkcija kao što je dugotrajnost baterija u slučaju nestanka struje. Također, posjeduje i funkciju "samoćevotvorenja", što znači da će se automatski prilagođavati vašem rasporedu kućnog ogrjeva i hlađenja. Honeywell RTH230B nudi korisnicima optimalnu kontrolu nad grijanjem i hlađenjem, uz uštedu energije, što ga čini idealnim rješenjem za svaki dom ili poslovni prostor.

Općenito
BrendHoneywell
ModelRTH230B
Proizvodtermostat
JezikEngleski
Vrsta datotekeKorisnički priručnik (PDF)

Ne možete pronaći odgovor na svoje pitanje u priručniku? Odgovor na svoje pitanje možete pronaći u odjeljku ČPP o Honeywell RTH230B u nastavku.

Gdje je najbolje postaviti termostat?

Najbolje mjesto za termostat je soba u kojoj provodite najviše vremena, u mnogim slučajevima dnevni boravak ili kuhinja. Postavite termostat otprilike jedan i pol metara iznad poda, a ne smije biti izložen suncu niti postavljen na vanjskom zidu.

Koja je mrtva zona termostata?

Ako vaš termostat ima mrtvu zonu, vaša instalacija je, takoreći, „u mirovanju“. Termostat se uključuje samo kada, na primjer, razlika odstupa više od 2 ˚C od zadane sobne temperature.

Koja je idealna sobna temperatura?

Većina ljudi smatra da je idealna sobna temperatura između 19 i 22 stupnja Celzijusa.

Je li priručnik za Honeywell RTH230B dostupan na Hrvatski?

Nažalost, nemamo priručnik za Honeywell RTH230B dostupan na Hrvatski. Ovaj priručnik dostupan je na Engleski.

Vaše pitanje nije navedeno? Ovdje postavite svoje pitanje

Nema rezultata