Harley-Davidson J02830 (2003)

Harley-Davidson J02830 (2003) priručnik

  • INSTRUCTIONS
    -J02830
    REV. 07-16-2003
    BULLET CHROME DIRECTIONAL BAR KIT (HDI)
    General
    This directional bar fits 1999 and later HDI Touring and
    FLSTC/I models. Softail models only: This kit will not fit
    with the stock saddlebags, part numbers 90476-00 and
    90477-00.
    This kit contains the following items:
    QTY DESCRIPTION PART NO.
    1 Directional bar assembly 68997-04
    2 Hex screw, serrated flange 3576
    NOTE
    A Service Manual for your model motorcycle is available
    from any Harley-Davidson dealer.
    Installation
    To prevent accidental vehicle start-up, which could
    cause death or serious injury, disconnect battery cables
    (negative cable first) before proceeding.
    Disconnect negative (-) battery cable first. If positive (+)
    cable should contact ground with negative (-) cable con-
    nected, the resulting sparks can cause a battery explosion,
    which could result in death or serious injury. (00049a)
    1. Refer to the Service Manual and follow the instructions
    given to remove the seat and disconnect the battery
    cables, negative cable first.
    2. See Figure 1. Remove the taillight cover and disconnect
    the turn signal wires at the connectors shown in the illustra-
    tion. See the TAIL LAMP section of the Service Manual.
    3. Remove and discard the existing directional bar from the
    motorcycle, and the two hex head bolts and flat washers.
    4. Position the new Bullet Directional Bar Assembly to the
    rear fender, and secure the bar to the motorcycle using
    the two hex screws from the kit.
    5. Route the turn signal wires through the grommet in the
    fender. Connect the turn signal wires at the connectors
    shown in the illustration and replace the taillight cover
    IMPORTANT NOTE
    After making wire connections and routing wires, check to
    make sure that no wires are hanging loose from fender.
    Connect positive (+) battery cable first. If positive (+) cable
    should contact ground with negative (-) cable connected,
    the resulting sparks can cause a battery explosion, which
    could result in death or serious injury. (00068a)
    6. Connect the battery cables, positive cable first.
    7. Refer to the Service Manual, and follow instructions to
    install the seat.
    After installing seat, pull upward on front of seat to be
    sure it is in locked position. While riding, a loose seat
    can shift causing loss of control, which could result in
    death or serious injury. (00070a)
    Check for proper turn signal operation before riding
    motorcycle. Weak, intermittent, or non-operational lights
    indicate a poor connection or a short in the wires.
    Visibility is a major concern for motorcyclists. Improper
    turn signal operation may lead to an accident which
    could result in death or serious injury.
    8. Start the motorcycle and make sure that both turn signals
    function properly.
    1WARNING
    1WARNING
    1WARNING
    1WARNING
    1WARNING
    ®
    Kit Number 68617-04
    Figure 1. Turn Signal Connections
    i01526
    2
    1
    1. Left turn signal 2. Right turn signal

Imate li pitanja o Harley-Davidson J02830 (2003)?

Ovdje jednostavno postavite pitanje koje imate o Harley-Davidson J02830 (2003) drugim vlasnicima proizvoda. Navedite jasan i sveobuhvatan opis problema i svoje pitanje. Što bolje opišete svoj problem i pitanje, drugi vlasnici Harley-Davidson J02830 (2003) će Vam jednostavnije dati dobar odgovor.

Ovdje besplatno pročitajte Harley-Davidson J02830 (2003) priručnik. Pročitali ste priručnik, ali odgovara li on na Vaše pitanje? Postavite onda svoje pitanje na ovoj stranici drugim vlasnicima Harley-Davidson J02830 (2003).