Electronics Line EL-2764 priručnik

  • Page 1
    Wireless Carbon Monoxide Detector
    (Model EL-2764)
    Introduction
    Electronics Line Ltd.'s Wireless Carbon Monoxide Detector (CO) is an
    effective device for detecting the buildup of Carbon Monoxide. Upon
    detecting the CO gas, the unit emits an alarm and notifies the control panel.
    The main features of your CO gas detector include the following:
    Integrated transmitter designed for use with EL's wireless alarm
    systems
    Easy to install
    Monitoring of carbon monoxide in a continuous manner.
    Loud alarm (85 dB) when detecting a buildup of carbon monoxide
    Test button
    Continuous Self-testing function
    What You Should Know About Carbon Monoxide
    Carbon monoxide, also known as "CO" by the chemical form, is
    considered to be a highly dangerous poisonous gas, because it is
    colorless, odorless, tasteless and very toxic. In general, biochemistry
    phenomena have shown that the presence of CO gas inhibits the blood's
    capacity to transport oxygen throughout the body, which can eventually
    lead to brain damage.
    In any closed space (home, office, recreational vehicle or boat) even a
    small accumulation of CO gas can be quite dangerous.
    Although many products of combustion can cause discomfort and adverse
    health effects, it is CO gas which presents the greatest threat to life.
    Carbon monoxide is produced by the incomplete combustion of fuels such
    as natural gas, propane, heating oil, kerosene, coal, charcoal, gasoline, or
    wood. The incomplete combustion of fuel can occur in any device which
    depends on burning for energy or heat such as furnaces, boilers, room
    heaters, hot water heaters, stoves, grills, and in any gasoline powered
    vehicle or engine (e.g. generator set, lawnmower). Tobacco smoke also
    adds CO to the air you breathe.
    When properly installed and maintained, your natural gas furnace and hot
    water heater do not pollute your air space with CO. Natural gas is known
    as a "clean burning" fuel because under correct operating conditions, the
    combustion products are water vapor and carbon dioxide (CO
    2
    ), which is
    not toxic. The products of combustion are exhausted from furnaces and
    water heaters to the outside by means of a fuel duct or chimney.
    Correct operation of any burning equipment requires two key conditions:
    (a) An adequate supply of air for complete combustion.
    (b) Proper venting of the products of combustion from the furnace
    through the chimney, vent or duct to the outside.
    Typical carbon monoxide gas problems are summarized here:
    (a) Equipment problems, due to defects, poor maintenance,
    damaged and cracked heat exchangers
    (b) Collapsed or blocked chimneys or flues, dislodged, disconnected
    or damaged vents
    (c) Downdraft in chimneys or flues. This can be caused by very long
    or circuitous flue runs, improper location of flue exhaust or wind
    conditions
    (d) Improper installation or operation of equipment, chimney or vents
    (e) Air tightness of house envelop/inadequate combustion of air
    (f) Inadequate exhaust of space heaters or appliances
    (g) Exhaust ventilation/fireplace competing for air supply
    Potential sources of carbon monoxide in your home or office include
    clogged chimney, wood stove, wood or gas fireplace, automobile and
    garage, gas water heater, gas appliance, gas or kerosene heater, gas or
    oil furnace and cigarette smoke.
    Installing the Detector
    Selecting the installation location
    Since CO gas moves freely in
    the air, the suggested location
    is in or as near as possible to
    sleeping areas of the home,
    30 cm (12 inch) below the
    ceiling . For maximum
    protection, a CO detector
    should be located outside the
    primary sleeping areas or on
    each level of your home
    (see Fig 1 for suggested
    locations).
    Fig. 1
    IMPORTANT:
    This device is not suitable for installation in a hazardous location, as
    defined by the US National Electrical Code.
    Do not place the detector in the following areas:
    (a) Where the temperature may drop below 4C (39F) or exceed 38C
    (100F).
    (b) Near paint thinner fumes
    (c) Within 1.5 meter (5 feet) of open flame appliances such as furnaces,
    stoves and fireplaces
    (d) In exhaust streams from gas engines, vents, flues or chimneys
    (e) Do not place in proximity to an automobile exhaust pipe; this will
    damage the detector
    To install the detector:
    1. Remove the mounting bracket from your unit according to Fig. 2.
    1 2 3
    Fig. 2
    2. Hold the Mounting bracket against the wall as a template and mark the
    locations for the 2 mounting holes.
    3. Using a 5 mm (3/16-inch) drill bit, drill two holes at the marks and
    insert wall plugs (Fig 3).
    Fig. 3
    4. Secure the mounting bracket to the wall.
    5. Open the battery cover by pushing down on the battery snaps (Fig. 4).
    +
    -
    Fig. 4
    6. Insert the batteries (supplied) into the battery compartment. Pay
    attention to the correct battery polarity (+) (-) and close the battery
    compartment
    7. Line up the side slot of the bracket and the detector. Push the detector onto
    the mounting bracket until a click is heard (see arrow direction, Fig 3).
    8. Pull the detector outwards to make sure that it is securely attached to
    the mounting bracket.
    Transmitter/Receiver Communication Setup
    1. Set the panel to registration mode.
    2. Insert the batteries into compartment. The detector enters
    registration mode during which a transmission is sent every few
    seconds. You can terminate registration mode by pressing the Test
    Button. Test mode is automatically terminated after approximately
    five minutes.
    3. Verify that the detector has been identified by the receiver.
    LED & BUZZER Indication
    The LED light and the buzzer turn on and/or off to indicate various
    situations. There are four different light and buzzer operations:
    LED
    LED Status
    Buzzer
    Meaning
    Green
    (Power)
    Flashing On and Off
    every 30 seconds
    Normal condition
    RED
    (Alarm)
    Flashing
    Sequential Alarm
    Sound
    Alarm
    Orange
    Flashing On and Off
    Sequential Alarm
    Internal self test fail
    CARBON MONOXIDE DETECTOR
    GROUND
    FLOOR
    BASEMENT
    KITCHEN
    GARAGE
    BEDROOM
    BEDROOMBEDROOM

Imate li pitanja o Electronics Line EL-2764?

Ovdje jednostavno postavite pitanje koje imate o Electronics Line EL-2764 drugim vlasnicima proizvoda. Navedite jasan i sveobuhvatan opis problema i svoje pitanje. Što bolje opišete svoj problem i pitanje, drugi vlasnici Electronics Line EL-2764 će Vam jednostavnije dati dobar odgovor.

Ovdje besplatno pročitajte Electronics Line EL-2764 priručnik. Pročitali ste priručnik, ali odgovara li on na Vaše pitanje? Postavite onda svoje pitanje na ovoj stranici drugim vlasnicima Electronics Line EL-2764.