Britax-Römer EVOLVA 1-2-3 SL SICT

Britax-Römer EVOLVA 1-2-3 SL SICT priručnik

(1)
  • BRITAX RÖMER Kindersicherheit GmbH
    Blaubeurer Strasse 71
    D-89077 Ulm
    Germany
    T.: +49 (0) 731 9345-199/-299
    F.: +49 (0) 731 9345-210
    E.: service.de@britax.com
    www.britax.eu
    BRITAX EXCELSIOR LIMITED
    1 Churchill Way West
    Andover
    Hampshire SP10 3UW
    United Kingdom
    T.: +44 (0) 1264 333343
    F.: +44 (0) 1264 334146
    E.: service.uk@britax.com
    www.britax.eu
    Please take the time to read these instructions carefully and keep them
    to hand in the intended storage compartment
    05
    on the child safety seat at
    all times! The instructions must be kept with the child safety seat if the latter
    is passed on to a third party.
    3. SAFETY NOTES
    DANGER! For the protection of your child:
    In the event of an accident at a collision speed of more than 10km/h, the child
    safety seat may be damaged without the damage becoming immediately visible. In
    this case, the child safety seat must be replaced. Please dispose of it properly.
    Always have your child safety seat checked if you suspect it may have been
    damaged (e.g if it falls on the ground).
    Regularly check all important parts for damage. Ensure that all mechanical parts,
    in particular, are fully functional.
    Never lubricate or oil parts of the child seat.
    Never leave your child unattended in the child seat in the vehicle.
    Only allow your child to enter and exit the vehicle on the pavement side.
    Protect the child safety seat from intensive direct sunlight when it is not in use.
    The child safety seat can get very hot in direct sunshine. Children's skin is sensi-
    tive and could be harmed as a result.
    The more snugly the belt fits over your child's body, the better they will be protected.
    Avoid putting thick clothes on your child under the belt.
    Take regular breaks on long journeys in order to give your child the opportunity to
    run about and play.
    Use on the rear seat: Move the front seat far enough forwards to ensure that your
    child's feet cannot hit the backrest of the front seat (to prevent risk of injury).
    If your child tries to open
    the red ISOFIT safety button
    06
    or a buckle, stop the
    vehicle as soon as it is safe to do so. Check whether the child safety seat is correctly
    fastened and ensure that your child is correctly secured. Explain to your child the
    dangers associated with their actions.
    DANGER! For the protection of all vehicle occupants:
    In the case of an emergency stop or an accident, unsecured persons or objects may
    cause injury to other vehicle occupants. Please always check that:
    the backrests of the vehicle seats are locked, e.g. that a foldable rear seat bench
    latch is engaged.
    all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are
    secured.
    all persons in the vehicle have their seat belts fastened.
    the child safety seat is always secured when it is in the vehicle, even if no child is
    being transported.
    WARNING! For your protection when handling the child seat:
    Never use the child safety seat free standing, not even for test sitting.
    To avoid damage, ensure that the child safety seat is not jammed in between
    hard objects (car door, seat rails, etc.).
    Keep the child safety seat in a safe place when it is not in use. Do not place any
    heavy objects on the seat and do not store it directly next to sources of heat or in
    direct sunlight.
    4. USE IN THE VEHICLE
    Please observe the instructions for using children's restraining systems in the operating
    instructions of your vehicle. The seat can be used in vehicles with ISOFIX anchoring systems
    (see type list) and in vehicles with a 3-point belt.
    To determine which seats are approved for use with child safety seats that meet the
    requirements for weight classes 9 to 18 kg and 15 to 36 kg, please refer to the operating
    instructions of your vehicle.
    9-36 kg
    The EVOLVA 1-2-3 SL SICT is approved for two dierent methods of installation:
    Group Installation method Means by which child
    is secured
    Section of
    user instructions
    1 (9-18 kg) Vehicle belt With 5-point harness A
    1 (9-18 kg) Vehicle belt + soft latch With 5-point harness A
    2+3 (15-36 kg) Vehicle belt Vehicle belt B
    2+3 (15-36 kg) Vehicle belt + soft latch Vehicle belt B
    a)
    This means that the child safety seat may only be used in vehicles that are listed in the enclosed
    vehicle type list. This type list is consistently kept up to date.
    The latest version can be obtained from us or from www.britax.com
    You can use your child safety seat as follows:
    In the direction of travel Yes
    Against the direction of travel No
    1)
    With 2-point harness No
    With 3-point belt
    2)
    Yes
    with ISOFIX fastening points (be-
    tween seat surface and backrest)
    Yes
    On front passenger seat
    Yes
    3)
    On outer rear seat Yes
    On centre rear seat
    (with 3-point belt)
    Yes
    4)
    1) Use on a rearward-facing vehicle seat (e.g. in a van or minibus) is only permitted if the vehicle
    seat is also approved for use by adults. The seat may not be in the area of eect of an airbag.
    2) The safety belt must be approved to ECE R 16 or a comparable standard, e.g. see whether
    there is an "E" or "e" in a circle on the belt test label.
    3) If there is a front airbag: Slide the vehicle seat a long way back and refer to any instructions
    in the vehicle owner's manual.
    4) Cannot be used if the vehicle seat is equipped with only a 2-point belt.
    PAGE I
    7. HARNESS BUCKLE CARE
    1. PRODUCT OVERVIEW
    DISPOSAL:
    Please observe the waste disposal regulations in your country.
    Disposal of packaging Container for cardboard boxes
    Seat cover Residual waste, waste incineration
    Plastic parts To be placed in the corresponding
    container according to labelling
    Metal parts Container for metals
    Belt straps Container for polyester
    Buckle and tongue Residual waste
    6. CARE AND MAINTENANCE
    Please ensure that you only use original BRITAX RÖMER replacement
    covers, as the seat cover is an integral part of the child safety seat and fulls
    important functions to ensure the smooth operation of the system. Replace-
    ment covers are available from your dealer.
    The cover can be removed and washed in accordance with the instruc-
    tions on the wash care label.
    The plastic parts can be cleaned using soapy water. Do not use any caus-
    tic cleaning agents (such as solvents).
    DANGER! The child seat must not be used without the seat cover.
    CAUTION! Never remove the buckle tongues
    30
    from the straps.
    9 to 36 kg
    (~9 months to
    12 years of age)
    www.britax.com
    2000025513 16/08
    GB
    EVOLVA 1-2-3 SL SICT
    User instructions
    5. CHANGING THE HARNESS
    Removing the 5-point harness
    1. Loosen the harness straps as far as possible (see 9.1).
    2. Push the shoulder strap adjuster
    24
    all the way up
    (see 8.1).
    3. Unhook the shoulder straps
    13
    from the connecting
    piece
    14
    .
    4. Clip the connecting piece
    14
    at the bottom of the
    backrest
    04
    into its holder
    11
    .
    5. Push down the strap loops of the shoulder pads
    18
    from the base of the shoulder strap adjuster
    24
    .
    6. Pull the shoulder straps
    13
    and the strap loops of the
    shoulder pads
    18
    out of the belt slots.
    7. Undo the Velcro fastener on the crotch cushion
    21
    and
    remove it.
    8. On the bottom of the seat, unhook the adjusting strap
    23
    from the metal plate
    27
    .
    9. Turn the metal plate
    27
    (that holds the harness buckle
    19
    to the seat shell) on end and push it upwards
    through the belt slot
    28
    .
    10. Release the harness buckle
    19
    .
    11. Push the straps and buckle tongues
    30
    through the lap
    belt slots in the cover.
    12. Place the harness buckle
    19
    under the cover and inside
    the storage compartment
    31
    of the backrest
    04
    .
    13. Push the adjusting strap
    23
    under the cover.
    14. Fix the shoulder pads
    18
    and shoulder straps
    13
    in the
    rubber loops
    32
    at the feed-through points
    15
    .
    Installing the 5-point harness
    To install the straps, follow the steps in reverse order.
    DANGER! Tug on the shoulder straps firmly
    13
    to make
    sure that the 5-point harness is secure.
    Removing the cover
    1. Adjust the headrest by moving it up
    16
    (see 9.1).
    2. Unhook the edge of the cover and the rubber loops on
    the back of the headrest
    16
    .
    3. Pull o the cover of the headrest
    16
    .
    4. Unhook the rubber loops from the retaining screws on
    the backrest
    04
    .
    5. Loosen the shoulder straps
    13
    (see 9.2).
    6. Undo the Velcro fastener on the crotch cushion
    21
    and
    remove it.
    7. Open the snaps
    on the left and right-hand sides of the
    backrest cover
    04
    .
    8. Unthread the harness buckle
    19
    and the adjusting strap
    23
    from the cover.
    9. On the bottom of the seat, unhook the rubber loop of
    the cover from the retaining screws and cover flaps
    24
    .
    10. Working from the side, carefully pull the edge of the
    cover on the backrest
    04
    over the SICT
    08
    .
    11. Slide the cover with opening over the headrest
    16
    .
    The cover can now be washed in accordance with the
    instructions on the wash care label.
    Re-fitting the cover
    Proceed in reverse order to re-fit the cover.
    WARNING! Ensure that the straps are not twisted and
    that they have been correctly inserted in the belt slots on
    the cover.
    To ensure the safety of your child, it is absolutely essential that the harness
    buckle continues to function correctly. Harness buckle malfunctions are usually
    caused by a build-up of soiling or by external objects.
    Possible faults:
    When you press the red release button, it takes a long time for the buckle
    tongues to be ejected.
    The buckle tongues no longer engage (i.e. when you try to push them in, they
    pop out again).
    The buckle tongues engage without an audible "click".
    The buckle tongues are dicult to push in (you feel a certain amount of
    resistance).
    Remedy: Clean the harness buckle so that it functions properly again:
    Cleaning the harness buckle
    1. Remove the harness buckle
    19
    (see 5.1).
    2. Soak the buckle
    19
    in warm water containing washing-up
    liquid for at least an hour.
    3. Rinse the buckle
    19
    thoroughly and dry it.
    4. Turn the metal plate
    27
    on end and push it downwards
    through the belt slot
    28
    in the cover and through the
    seat shell.
    5. Turn the metal plate
    27
    90° and hook the adjusting strap
    23
    into the metal plate
    27
    (5.8).
    DANGER! Tug hard on the harness buckle
    19
    to make
    sure that it is secure.
    6. Push the crotch cushion
    21
    into the belt slot and use the
    Velcro fastener to fix it to the harness buckle.
    01 02
    03
    01
    ISOFIX fastening points (car)
    06
    ISOFIT Locking button
    02
    ISOFIX insertion aids
    07
    ISOFIT locking arms
    03
    Headrest adjuster
    08
    SICT
    04
    Backrest
    09
    Cover flap
    05
    Compartment for the user instructions
    10
    ISOFIT adjustment button
    09
    06
    04
    07
    If you have any questions regarding the use of the product, please feel free to contact us:
    2. APPROVAL
    BRITAX RÖMER
    Vehicle child
    safety seat
    Tested and approved according to ECE* R 44/04
    *ECE = European Standard for Child Safety Equipment
    Group Body weight
    EVOLVA 1-2-3 SL
    SICT
    I 9 to 18 kg
    II+III 15 to 36 kg
    The child safety seat has been designed, tested and approved according
    to the requirements of the European Standard for Child Safety Equipment
    (ECER44/04). The seal of approval E (in a circle) and the approval number are
    located on the orange approval label (sticker on the child safety seat).
    DANGER! This approval will be invalidated if you make any modifications to
    the child safety seat. Only the manufacturer is permitted to make modifica-
    tions to the child safety seat.
    WARNING! Use the EVOLVA 1-2-3 SL SICT exclusively for securing your
    child in your vehicle. It is in no way suitable for use as a seat or toy in the
    home.
    DANGER! Never secure your child or the child safety seat with a 2-point
    belt. If you secure your child in the child seat with only a 2-point belt, this
    may cause serious injuries to your child in the event of an accident and could
    even result in their death.
    DANGER! Never use installation method A for the child safety seat unless
    the harness buckle and shoulder pads are properly attached (the straight
    edges of the shoulder pads must be pointing towards each other). Make
    sure that the metal plate of the harness buckle is correctly attached.
    WARNING! Ensure that the straps are not twisted, that they have not been
    accidentally interchanged and that they have been correctly inserted in the
    belt slots on the cover.
    05
    08
    10
    19
    19
    27
    28
    11
    14
    04
    24
    18
    23
    27
    27
    19
    28
    31
    19
    04
    21
    1813
    32
    15
    32
    13
    14
    16
    21
    04
    04
    23
    24
    24
    04
    08
    16
    28
    160908_EVOLVA_123_SICT_DRAFT_GB_GRAFIKEN.indd 1 9/7/2016 9:04:53 PM
Britax-Römer EVOLVA 1-2-3 SL SICT

Trebate pomoć?

Broj pitanja: 0

Imate li pitanja u vezi s proizvodom EVOLVA 1-2-3 SL SICT trgovačke marke Britax-Römer ili vam treba pomoć? Ovdje postavite svoje pitanje. Navedite jasan i sveobuhvatan opis problema i vašeg pitanja. Što više pojedinosti navedete za svoje pitanje i pitanje, lakše je drugim vlasnicima proizvoda EVOLVA 1-2-3 SL SICT trgovačke marke Britax-Römer pravilno odgovoriti na vaše pitanje.

Ovdje besplatno pogledajte priručnik za proizvod EVOLVA 1-2-3 SL SICT trgovačke marke Britax-Römer. Ovaj je priručnik pod kategorijom , a ocijenio ga je sljedeći broj osoba: 1 prosječnom ocjenom od 7.5. Ovaj je priručnik dostupan na sljedećim jezicima: Engleski. Imate li pitanja u vezi s proizvodom EVOLVA 1-2-3 SL SICT trgovačke marke Britax-Römer ili vam treba pomoć? Ovdje postavite svoje pitanje

Značajke proizvoda EVOLVA 1-2-3 SL SICT trgovačke marke Britax-Römer

Brend Britax-Römer
Model EVOLVA 1-2-3 SL SICT
Proizvod Sjedalica za automobil
EAN 4000984200539
Jezik Engleski
Vrsta datoteke PDF
Značajke
Boja proizvoda Graphite, Grey
Skupina autosjedalica 1-2-3 (9 - 36 kg; 9 mjeseci - 12 godine)
Tip montaže ISOFIX + pojas za sjedalo
Način pričvršćivanja remena Na 5 mjesta
Naslon za glavu
Podesivi naslon za leđa
Podesivi naslon za glavu
Minimalni kapacitet nosivosti 9kg
Maksimalna težina vaganja 36kg
Težina i dimenzije
Širina 510mm
Dubina 480mm
Visina (minimalna) 610mm
Visina (maksimalna) 860mm
Težina 8600g

Povezani priručnici za proizvode

Sjedalica za automobil Britax-Römer

prirucnici.hr

Tražite priručnik? prirucnici.hr osigurava da u trenu pronađete priručnik koji tražite. Naša baza podataka sadrži više od milijun PDF priručnika za više od 10,000 robnih marki. Svaki dan dodajemo najnovije priručnike pa ćete uvijek pronaći proizvod koji tražite. Vrlo je jednostavno: samo u tražilicu upišite naziv robne marke i vrstu proizvoda i odmah ćete vidjeti priručnik po svom izboru na Internetu, besplatno.

prirucnici.hr

© Autorska prava 2020 prirucnici.hr. Sva prava pridržana.